Husqvarna 96193005500 owner manual Skid Plate

Page 24

REPAIR PARTS SNOW THROWER - MODEL NUMBER 924SB (96193005500)

AUGER HOUSING / IMPELLER ASSEMBLY

				4	2
					2		3
							3
			1
	4	1
	4
					5
	2
					KEY	PART	DESCRIPTION
					NO.	NO.	DESCRIPTION
					1	532 43 27-65 PLASTIC RETAINER
					2	532 42 77-62 AUGER BALL BEARING
3		5			3	532 17 95-82 SCREW 5/16−18 X 1.00
		5			4	874 78 04-26 SCREW 1/4−20 X .625
			01.07.029-A		4	874 78 04-26 SCREW 1/4−20 X .625
			01.07.029-A		5	873 80 04-00	NUT 1/4-20
					5	873 80 04-00	NUT 1/4-20

3

	2	1
2		1
2

3

01.11.002-B 1

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	532 43 57-85	SKID PLATE
2	872 27 05-06	CARRIAGE BOLT 5/16−18 X .750
3	532 75 11-53	NUT 5/16−18

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty.

24

Image 24

Contents 924SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingTo USE Fuel SHUT-OFF Valve See Fig To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigTo Adjust Skid Plates See Fig Before Starting the EngineScraper BAR See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig To Adjust Cable Tension See Fig To Remove Wheels See FigCarburetor Engine SpeedStorage OtherFuel System Engine OILTroubleshooting Auger Assembly LH Auger Assembly RHKEY Part Description Scraper BARExploded Impeller BearingTool Clip PlugSkid Plate Service Part Deflector Cable Gray Deflector SealKnob Black POP Rivet532 42 82-74 LEVER/CABLE Rotator Assembly Cable Assembly Adjustable GrayCable Assembly Heat Shield Gray Rotator Pivot BracketRepair Parts Snow Thrower Model Number 924SB Handles Handle GripWasher Lower Tube Gray532 42 14-48 Headlight Bezel Gray SHOULDERSCREW10-24X.625Bulb RetainerRepair Parts Snow Thrower Model Number Repair Parts Snow Thrower Model Number 924SB SpacerKnob RED Handle KnobRepair Parts Snow Thrower Model Number 924SB Drive Axle ShaftRoll PIN 3/16 Gear532 17 53-44 Trunnion Bearing Assembly Control Shaft AssemblyFlange Bearing HEX ShaftKEY Part 532 42 86-84 Cover Assembly 532 43 60-70 Complete LCT EngineFrame KEY Part Description 532 42 92-69 Engine Mounting PlateIdler Pulley Repair Parts Wheels532 43 58-27 Steer Cable Bracket LH Steer Cable Bracket RH532 40 CoverWheel Lobe Axle LobeRepair Parts Snow Thrower Model Number 924SB BAG of Parts Power CordKEY Part Description 532 42 26-63 Safety Ignition KEY Retainer PINRepair Parts Snow Thrower Model Number 924SB Decals 532 18 10-35 DECAL, DANGER, Deflector532 42 95-69 DECAL, TRACT/CLUTCH Lever Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission Years 532 43 56-49 08.13.10 AP