Husqvarna 96193005500 owner manual Idler Pulley

Page 35

REPAIR PARTS SNOW THROWER - MODEL NUMBER 924SB (96193005500)

CHASSIS / ENGINE / PULLEYS

24

11

13

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION

1532 40 80-07 IMPELLER BELT

2532 41 97-44 TRACTION BELT

3532 43 58-02 IDLER ARM BRACKET

4	532 18 05-23	IDLER PULLEY
5	532 42 65-89	NUT 5/16-18

23	22
	14
	21
	20
14	21
	20

12 14 15

6

7

10

8

19

3

18

17

16

5

4

6874 78 05-24 SCREW 5/16-18 X 1 .50

7532 43 58-01 IDLER BRACKET

8532 42 88-67 SCREW 5/16-18 X .625

9532 42 42-97 SHOULDER BOLT 5/16-18 X .500

10532 75 11-53 NUT 5/16-18 NYLOCK

11532 18 77-86 TRACTION IDLER ARM

12532 18 05-22 TRACTION PULLEY

13874 78 05-20 SCREW 5/16-18 X 1 .00

14	532 05 92-89	WASHER
15	873 80 05-00	NUT 5/16-18
16	532 85 10-84	SCREW 3/8-24 X 1.375
17	532 40 00-26	WASHER

18532 42 64-91 PULLEY ENG IMPELLER

19532 42 64-90 PULLEY ENG TRACTION

20874 61 05-16 SCREW 5/16-18 X 1 .00

21810 04 05-00 LOCKWASHER 5/16

22	532 15 54-52 BELT GUIDE

23811 05 05-00 LOCKWASHER 5/16

24532 17 53-31 IDLER BUSHING

01.21.003-C

9

1

2

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 35

Image 35

Contents 924SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonUnfold Upper Handle Install Speed Control ROD See FigsInstall Traction Drive Control ROD See Figs Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigCheck Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Scraper BAR Auger Assembly LHAuger Assembly RH KEY Part DescriptionExploded Plug ImpellerBearing Tool ClipSkid Plate POP Rivet Service Part Deflector Cable GrayDeflector Seal Knob BlackRotator Pivot Bracket 532 42 82-74 LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Gray Cable Assembly Heat Shield GrayLower Tube Gray Repair Parts Snow Thrower Model Number 924SB HandlesHandle Grip WasherRetainer 532 42 14-48 Headlight Bezel GraySHOULDERSCREW10-24X.625 BulbRepair Parts Snow Thrower Model Number Handle Knob Repair Parts Snow Thrower Model Number 924SBSpacer Knob REDGear Repair Parts Snow Thrower Model Number 924SB DriveAxle Shaft Roll PIN 3/16HEX Shaft 532 17 53-44 Trunnion Bearing AssemblyControl Shaft Assembly Flange BearingKEY Part KEY Part Description 532 42 92-69 Engine Mounting Plate 532 42 86-84 Cover Assembly532 43 60-70 Complete LCT Engine FrameIdler Pulley Steer Cable Bracket RH Repair PartsWheels 532 43 58-27 Steer Cable Bracket LHAxle Lobe 532 40Cover Wheel LobeRetainer PIN Repair Parts Snow Thrower Model Number 924SB BAG of PartsPower Cord KEY Part Description 532 42 26-63 Safety Ignition KEY532 42 95-69 DECAL, TRACT/CLUTCH Lever Repair Parts Snow Thrower Model Number 924SB Decals532 18 10-35 DECAL, DANGER, Deflector Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission Years 532 43 56-49 08.13.10 AP