Husqvarna 96193005500 owner manual Install Auger Control ROD See Figs

Page 6

ASSEMBLY / PRE-OPERATION

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

1.Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. Slide straight rod end through the small hole in the vinyl sleeve. Hook spring in hole in rod end.

2.Hook end of spring into control arm with loop opening up as shown. (See Fig. 5)

3.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

VINYL

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

Fig. 5

	AUGER CONTROL ROD	AUGER
	RETAINER	CONTROL
	RETAINER	LEVER
	SPRING	LEVER
	SPRING
		AUGER
	CONTROL
	BRACKET

Fig. 6

INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotator head over chute bracket. If neces- sary, rotate chute assembly to align square and pin on un- derside of chute rotator head with holes in chute bracket.

3.With chute rotator head and chute bracket aligned, position chute rotator head on pin and threaded stud of mounting bracket.

4.Install 3/8 washer and locknut on threaded stud and tighten securely.

CHUTE
ROTATOR		3/8 LOCKNUT
HEAD
		3/8 WASHER
		PIN
		THREADED
		STUD
	ALIGN BEFORE	ROTATOR HEAD
CHUTE	ALIGN BEFORE	MOUNTING
BRACKET	TIGHTENING LOCKNUT	BRACKET

Fig. 7

6

Image 6

Contents 924SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressurePrimer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigTo Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigScraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting KEY Part Description Auger Assembly LHAuger Assembly RH Scraper BARExploded Tool Clip ImpellerBearing PlugSkid Plate Knob Black Service Part Deflector Cable GrayDeflector Seal POP RivetCable Assembly Heat Shield Gray 532 42 82-74 LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Gray Rotator Pivot BracketWasher Repair Parts Snow Thrower Model Number 924SB HandlesHandle Grip Lower Tube GrayBulb 532 42 14-48 Headlight Bezel GraySHOULDERSCREW10-24X.625 RetainerRepair Parts Snow Thrower Model Number Knob RED Repair Parts Snow Thrower Model Number 924SBSpacer Handle KnobRoll PIN 3/16 Repair Parts Snow Thrower Model Number 924SB DriveAxle Shaft GearFlange Bearing 532 17 53-44 Trunnion Bearing AssemblyControl Shaft Assembly HEX ShaftKEY Part Frame 532 42 86-84 Cover Assembly532 43 60-70 Complete LCT Engine KEY Part Description 532 42 92-69 Engine Mounting PlateIdler Pulley 532 43 58-27 Steer Cable Bracket LH Repair PartsWheels Steer Cable Bracket RHWheel Lobe 532 40Cover Axle LobeKEY Part Description 532 42 26-63 Safety Ignition KEY Repair Parts Snow Thrower Model Number 924SB BAG of PartsPower Cord Retainer PINRepair Parts Snow Thrower Model Number 924SB Decals 532 18 10-35 DECAL, DANGER, Deflector532 42 95-69 DECAL, TRACT/CLUTCH Lever Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission Years 532 43 56-49 08.13.10 AP