Husqvarna 96193005500 Install Chute Deflector Remote Control See Figs, Check Tire Pressure

Page 7

ASSEMBLY / PRE-OPERATION

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9)

1.Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely.

2.Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt and 1/4-20 locknut as shown. Tighten nut securely. Cable eyelet will be loose on shoulder bolt.

3.Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown.

	1/4-20	SPRING
	1/4-20	CHUTE
	SHOULDER	CHUTE
	SHOULDER	DEFLECTOR
	BOLT	DEFLECTOR
	BOLT
		HOOK
		BETWEEN
		HEX NUTS
		ON CHUTE
	1/4-20	ROTATER
	LOCKNUT	HEAD
		5/16-18
		CARRIAGE
		BOLT
	CABLE
	EYELET
	REMOTE
	CABLE
	BRACKET
	5/16-18
	LOCKNUT

Fig. 8

CHUTE DEFLECTOR

CONTROL LEVER

Fig. 9

CHECK TIRE PRESSURE

The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

•Reduce tire pressure to 14-17 PSI.

Image 7

Contents 924SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotator Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See FigTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Throw Snow See FigCheck Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Scraper BAR Auger Assembly LHAuger Assembly RH KEY Part DescriptionExploded Plug ImpellerBearing Tool ClipSkid Plate POP Rivet Service Part Deflector Cable GrayDeflector Seal Knob BlackRotator Pivot Bracket 532 42 82-74 LEVER/CABLE Rotator AssemblyCable Assembly Adjustable Gray Cable Assembly Heat Shield GrayLower Tube Gray Repair Parts Snow Thrower Model Number 924SB HandlesHandle Grip WasherRetainer 532 42 14-48 Headlight Bezel GraySHOULDERSCREW10-24X.625 BulbRepair Parts Snow Thrower Model Number Handle Knob Repair Parts Snow Thrower Model Number 924SBSpacer Knob REDGear Repair Parts Snow Thrower Model Number 924SB DriveAxle Shaft Roll PIN 3/16HEX Shaft 532 17 53-44 Trunnion Bearing AssemblyControl Shaft Assembly Flange BearingKEY Part KEY Part Description 532 42 92-69 Engine Mounting Plate 532 42 86-84 Cover Assembly532 43 60-70 Complete LCT Engine FrameIdler Pulley Steer Cable Bracket RH Repair PartsWheels 532 43 58-27 Steer Cable Bracket LHAxle Lobe 532 40Cover Wheel LobeRetainer PIN Repair Parts Snow Thrower Model Number 924SB BAG of PartsPower Cord KEY Part Description 532 42 26-63 Safety Ignition KEY532 18 10-35 DECAL, DANGER, Deflector Repair Parts Snow Thrower Model Number 924SB Decals532 42 95-69 DECAL, TRACT/CLUTCH Lever Limitations and Exclusions HOW to Obtain Service Consumer Wheeled Warranty Chart Front Mounted Deck Riders Engine Transmission Years 532 43 56-49 08.13.10 AP