Tascam CD-X1700 English Before you start, Environmental conditions, Beware of condensation

Page 6

English

1. Before you start

 

 

1.1 Environmental conditions

The TASCAM CD-X1700 may be used in most areas, but to maintain top performance, and prolong operating life, observe the following environmental conditions:

The nominal temperature should be between 5°C and 35°C (41°F and 95°F).

Relative humidity should be 30 to 90 degrees non- condensing.

Make sure that the drive unit is mounted in a level position for correct operation.

The units should be mounted, using the supplied rack mounting kits. A typical configuration is shown below, but other configurations are possible:

NOTE

If the disc trays are more than 5 degrees away from the horizontal, they will not open or close.

Do not install this apparatus in a con- fined space such as a book case or simi- lar unit.

1.2 Beware of condensation

If the player (or a compact disc) is moved from a cold to a warm place, or used after a sudden temperature change, there is a danger of condensation; vapor in the air could condense on the internal mechanism, making correct operation impossible. To prevent this, or if this occurs, leave the player for one or two hours with the power turned on, then turn the power off and on again.

1.3 Handling of discs

The unit has been designed specifically for

reproduction of discs bearing the mark. No other discs can be reproduced.

Observe the following:

Always place the compact discs in the trays with their label facing upward (compact discs can only be played on one side).

To remove a disc from its storage case, press down on the center of the case, and lift the disc out, holding it carefully by the edges.

Finger marks and dust should be carefully wiped off the disc's recorded surface with a soft cloth. Unlike conventional records, the compact disc has no grooves to collect dust and microscopic debris, so gently wiping with a soft cloth should remove most particles.

Wipe in a straight motion from the inside to the outside of the disc. Small dust particles and light stains will have absolutely no effect on reproduc- tion quality.

Never use such chemicals as record sprays, anti- static sprays or fluid, benzine or thinner to clean compact discs. Such chemicals will do irrepara- ble damage to the disc's plastic surface.

Discs should be returned to their cases after use to avoid serious scratches that could cause the laser pickup to "skip".

Don't expose discs to direct sunlight or high humidity and temperature for extended periods. Long exposure to high temperature can warp the disc.

Only use circular compact discs. Avoid using non-circular promotional, etc. discs.

To keep the laser pickups clean, don't touch them. For the same reason, don't leave the disc trays open unnecessarily.

6 TASCAM CD-X1700 DUAL CD PLAYER

Image 6
Contents CD-X1700 English Important for U.K. CustomersDo not cut off the mains plug from this equipment Important Safety Instructions Safety Information Table of contents English Beware of condensation English Before you startEnvironmental conditions Handling of discsFunctions and Controls English Main Unit Front PanelMain Unit Rear Panel Remote Controller Top Panel English Functions and ControlsReverse key Scratch keyBrake key Search keyRemote Controller Bottom Panel Remote Controller LCD English Playback operation CUEFlash Start Adjusting the tempo B LoopingKey Original Using the Tempo sliderPitch Bending Auto BPM and TAP keyBrake More advanced operation EnglishKey control ScratchingEnglish More advanced operation Effect time settingEffect level setting Synchronizing the effect time withReverse play SamplerSampling Track Memory / Recall Track MemoryMemory data RecallAuto Ready Fader StartRelay Play Auto CueProgrammed Play Create the programEdit program Insert program Delete programPreset menu 13. MP3 file playbackPlaying the MP3 file Backup Memory Preset NumberFunction Specifications English Error MessagesEspañol Instrucciones Importantes DE SeguridadIndice Español Instrucciones Importantes DE SeguridadCuidado con la condensación Español Antes de empezarCondiciones ambientales Manejo de los discosFunciones y controles Español Unidad principal panel frontalUnidad principal panel trasero Tecla Open Español Funciones y controlesMando a distancia Panel superior Tecla P.MODE / PGMTecla Brake Tecla TAP / DisplayTecla Scratch Tecla ReverseMando a distancia Panel inferior Mando a distancia LCDPantalla de tiempo # Indicador PGM$ Indicador MP3 Indicador FlashEspañol Reproducción Inicio flashBucle A-B Ajuste del tempo Inflexión tonalClave original Frenado Otras funciones avanzadas EspañolControl de clave EfectosSincronización del tiempo del efecto con el BPM Otras funciones avanzadasAjuste del tiempo del efecto Ajuste del nivel de efectoUso del bucle A-B como fuente del muestreo Reproducción al revésMuestreo Reproducción del samplerEspañol Otras funciones avanzadas Memoria de pista / cargaMemoria de pista Datos memorizados CargaReproducción consecutiva 10. Búsqueda automáticaInicio por fader Espera automáticaReproducción programada Edición del programaCreación del programa Inserción de programa Borrado de programaMenú preset Reproducción de ficheros MP3Reproducción de archivo MP3 Número preset Elemento Parámetro Función Copia de seguridadMensajes de error Especificaciones técnicas EspañolDimensions / Dimensiones Teac Corporation

CD-X1700 specifications

The Tascam CD-X1700 is a robust, professional-grade CD player that has earned a reputation for reliability in various audio environments, from live performances to studio settings. Designed with musicians, DJs, and audio engineers in mind, the CD-X1700 combines a wealth of features that make it a versatile tool for handling audio playback.

One of the standout features of the CD-X1700 is its dual CD drive capability. This allows users to seamlessly switch between two discs, which is particularly useful in live settings where uninterrupted playback is essential. The player supports both standard CD formats and CD-R/RW discs, providing flexibility in playback options.

The CD-X1700 boasts a range of playback options including cueing, looping, and pitch control. The quick cueing function lets users start playback at any point in a track instantly, while the looping feature enables extended play for specific sections, making it ideal for practice or performance. The pitch control function allows users to adjust the playback speed without altering the tonal quality of the audio, providing creative flexibility for musicians.

Connectivity is another strong point for the CD-X1700. It features balanced and unbalanced outputs, allowing for straightforward integration into various audio setups. Additionally, MIDI compatibility allows for external control and synchronization with other devices, making it an essential component in a comprehensive sound system.

The user interface of the CD-X1700 is intuitive, with a clear LED display and well-laid-out controls. This ensures that users can navigate through tracks and features with ease, even in high-pressure environments. The player also includes a programmable memory function, enabling users to create customized playlists for performances.

Durability is a key characteristic of the Tascam CD-X1700. Built with high-quality materials, it is designed to withstand the rigors of frequent transport and use, making it suitable for both touring musicians and fixed installation setups. Its rugged construction, combined with high-performance components, assures long-term reliability.

Overall, the Tascam CD-X1700 is an impressive piece of audio equipment that adeptly bridges the gap between utility and performance. With its feature set and reliable construction, it's no wonder that this CD player has become a favorite among professionals who demand high quality in their audio playback solutions. Whether for live events or studio use, the Tascam CD-X1700 remains a trusted asset in the audio industry.