Meyer 7200 manual Spinner Material Guides, Spring Loaded Material Guide Adjustment, 1/2

Page 19

The side shaft chain drive (PTO input shaft to the side line shaft drive sprocket, figure 12) is automatically tensioned by a spring loaded idler nylon roller. The extension spring should extend 2" from its neutral 5" total length.

Manual adjustment for the automatic tensioning idler, nylon roller assembly is located at the right rear of the spreader’s front bearing mounting plate.

SIDE LINE SHAFT

IDLER NYLON

ROLLER

DRIVE SPROCKET

 

 

SPRING LOADED

 

ADJUSTER

 

PTO INPUT

FIGURE 12. SIDE SHAFT CHAIN DRIVE

SPINNER MATERIAL GUIDES

Regularly inspect and adjust two spinner material guides located at both the left rear and right rear of the spreader. Create a 1/4-1/2” clearance between material guides and spinner teeth, figure 13. Maintain the recom- mended clearances for maximum spreading pattern. Adjust to prevent excessive manure build-up on mate- rial guide inner surfaces. Adjust to prevent manure chunks or foreign object lodging between material guides and spinner teeth.

NOTE: Excessive lodging can cause premature spinner tooth wear, “bent-over” or even breakage.

SPRING LOADED MATERIAL GUIDE ADJUSTMENT

Adjustments for the 1/4-1/2” clearance of each material guide to spinner tooth is made by tightening or loosen- ing the 1” nut on the material guide spring linkage shaft assembly. Tighten nut to increase clearance and loosen nut to decrease clearance between the material guides and spinner teeth. Once recommended clearance is ob- tained turn spinners over by hand in the direction by

1/4”-1/2”

FIGURE 13. MATERIAL GUIDE

CLEARANCE

which the spreader would turn to check clearance. Do not turn in the opposite direction as front chain tightener damage could occur.

SHEAR ARM MATERIAL GUIDE ADJUSTMENT

Adjustment for the1/4-1/2” clearance of each material guide to spinner tooth is made by loosening the jam nut on the linkage arm and turning the linkage arm to either move the guide in closer or out farther from the spinner teeth. After adjustment has been made for the 1/4-1/2” clearance retighten the jam nut to hold the material guide in place. Once recommended clearance is ob- tained turn spinners over by hand in the direction by which the spreader would turn to check clearance. Do not turn in the opposite direction as front chain tightener damage could occur. If foreign objects enter the spinner area the front pivot bolt on the shear arm is designed to shear. The extension spring will pull the material guide away from the spinner until the shear bolt is replaced. The ½-13x3” grade 5 replacement machine bolts are stored on the left side plate for the gearbox mount channel. For replacement install with ½” flat washer on top of shear eye and on bottom of block and tighten ny- lon locknut firmly.

Model 7200

-19-

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 12/03 Manufactured byTable of Contents VII MANUFACTURER’S WarrantyRemember Farm Equipment Buyers Trust the Name Meyer IntroductionModel No Serial No Date of Purchase Safety Precautions Safety First Decal H. Part no Industrial Series Gear BoxesPRE-OPERATION Tractor Drawbar & PTO SpecificationTractor Towing Size Requirements Material Estimated Weight PER Cubic FootMaximum Spreader Load Weights TransportingOptional Truck Mount Spreaders USE of Safety ChainFreezing Weather Operation Model Loading OperationUnloading Description Shear Sprocket InstructionsStorage After USE Driveline Attachment PTO SetupAdjustment on the Cutout Clutch PTO DrivelineLubrication Maintenance InformationNormal Operation Front Drive Roller Chains AdjustmentsThird Chain Drive 1/2 Spring Loaded Material Guide AdjustmentShear ARM Material Guide Adjustment Spinner Material GuidesDaily Lubrication every 8-12 loads LubricationWeekly Lubrication every 25-30 loads Monthly Lubrication PTO Drive Shaft Assembly Repair PartsKEY Meyer Part Description RPM-20 Spline / 1-3/4 Yoke WWE2480 80 Degree C.V KEY Part no Description KEY DescriptionAuger Drive Third Reduction This Page Intentionally Blank Front Shield & Side Shaft Drive KEY Description Auger Drive First Reduction RPM Auger Drive Second Reduction Auger Drive Second Reduction RH Auger Drive Final Reduction RH Auger Drive Final Reduction LH Auger Drive Final Reduction This Page Intentionally Blank BOX, Augers & Side Shaft KEY Description Unloading Gate and Gate Indicator Unloading Gate and Gate Indicator Spinners & Gearbox Shaft Drive Spinners & Gearbox Shaft Drive Spinner Gear Reducer Left Hand 11 #19-0029 KEY Description Spinner Gear Reducer Center 11 #19-0030KEY RPM Drive Part no Description Corner Gear Reducer Right HandHUBS, Axle & Tandem Assembly LADDER, Third AUGER, Gate Indicator & Lighting LADDER, Third AUGER, Gate Indicator & Lighting OIL-KIT KEY OEM Part no Description Instructions for Automatic Chain Oiler Symptom Problem Solution Augers Meyer Industrial Spreader Trouble ShootingDate Service Performed Meyer Industrial Spreader Maintenance RecordTire Inflation Tire Size PLY PSI Meyer Equipment Wheel TorqueThis Page Intentionally Blank Model Model Specifications Subject to Change Without Notice Meyer Industrial Spreader SpecificationsModel

7200 specifications

The Meyer 7200 is a cutting-edge agricultural tractor that stands out in the competitive landscape of modern farming equipment. Designed with efficiency and versatility in mind, it caters to the diverse needs of farmers and agricultural professionals. One of the primary features of the Meyer 7200 is its robust engine, which delivers remarkable power while maintaining fuel efficiency. With a maximum horsepower rating that exceeds expectations, this tractor is capable of handling a wide range of tasks, from plowing and tilling to hauling heavy loads.

The Meyer 7200 incorporates advanced technology that enhances its performance and usability. One notable technological feature is the integrated GPS guidance system, which assists farmers in optimizing field operations by providing precise navigation and mapping capabilities. This system not only minimizes overlaps during planting and spraying but also maximizes efficiency and productivity. The tractor is also equipped with an intuitive touchscreen interface, allowing operators to easily monitor performance metrics and adjust settings on-the-go.

Another significant characteristic of the Meyer 7200 is its exceptional maneuverability. The tractor is designed with a compact frame and a superior turning radius, making it adept at navigating tight corners and various terrains. This feature is particularly beneficial in smaller fields or crowded workspaces. Additionally, the tractor boasts an advanced suspension system that enhances ride comfort and stability, reducing operator fatigue during long hours in the field.

Durability is a hallmark of the Meyer 7200, with components built to withstand the rigors of daily farm work. The high-quality materials and robust construction ensure longevity and minimize maintenance requirements. Farmers can rely on the Meyer 7200 to perform reliably under heavy workloads, even in challenging weather conditions.

Safety is also a priority, with features such as roll-over protection structures and advanced braking systems. These safety enhancements provide peace of mind for operators, allowing them to focus on their tasks without added worry.

In summary, the Meyer 7200 is a powerful, efficient, and technologically advanced tractor that meets the demands of modern agriculture. With its powerful engine, integrated GPS system, exceptional maneuverability, durability, and safety features, the Meyer 7200 is an indispensable tool for farmers looking to elevate their productivity and ensure successful harvests. As the agricultural landscape continues to evolve, the Meyer 7200 stands ready to meet the challenges of today and tomorrow.
Top Page Image Contents