Meyer 7200 manual Instructions for Automatic Chain Oiler

Page 52

INSTRUCTIONS FOR AUTOMATIC CHAIN OILER

WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.

The automatic chain oiler attachment gives a squirt of clean oil to all roller chains every time that the spreaders rear gate, hydraulic cylinder is activated. In this way, the spreaders roller chains get oiled in direct proportion to the number of hydraulic cylinder cycles of the rear gate. This assures ade- quate lubrication.

New 30 weight oil, which is placed in the reservoir tank mounted on the spreader, is all that is needed to properly lubricate all roller chains and sprockets. The automatic chain oiler does not use any oil from the tractors hydraulic system. The hydraulic hose connected to the bottom of the oiler pump only serves to power the piston in the pump every time that the spreaders rear gate is opened.

Should the oil reservoir tank run dry, pour about a ½ cup of clean 30 weight oil into the tank. Allow time for the oil to run down into the oiler pump slowly and allow air to escape. After thirty minutes to one hour has passed, finish filling the reservoir tank. Make sure that all fittings and brackets are tight when finished filling the tank.

WARNING: HYDRAULIC FLUID ESCAPING UNDER PRESSURE CAN HAVE SUFFI- CIENT FORCE TO PENETRATE SKIN. KEEP ALL HOSES AND CONNECTIONS IN GOOD SERVICEABLE CONDITION. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL IN- JURY OR DEATH.

While running the tractors hydraulics only, open and close the spreaders rear gate several times. This will cycle the hydraulic cylinder leading to the oiler pump. Keep cycling until oil can be seen in all of the oil lines leading to the oiler brushes. (If you experience problems priming the oiler pump, you may need to bleed air out of the hydraulic hose where it is connected to the pump. Crack the fit- ting until oil comes out then re-tighten.) The hydraulic cylinder that the oiler pump is tied into is dou- ble acting and must reach 300 PSI of pressure to actuate the pump.

When replacing oiler brushes into brush holders, use regular ½"-20 nuts. Tighten nut finger tight ini- tially as some adjustment may be needed later. For best results, place brush holders over top of roller chains and directly on top of sprockets. Adjust brush holders so oiler brushes are pushed down into the roller chain approximately ½". Carefully tighten up the ½"-20 nuts on the oiler brushes. DO NOT over tighten as damage to the brush will occur. The plastic threads of the oiler brush will crack and then break off from the brush body.

IMPORTANT! The 5/32" oil line tubing can only be removed from an oiler brush by pushing in on the red plastic ring and pulling the tubing out while holding the ring down.

The oiler pump is set at the factory to deliver the maximum amount of oil per cycle. If less oil is de- sired, loosen the jam nut on the bottom of the pump and screw in the adjusting shaft 1/4" or approxi- mately 5 turns. It is not recommended to screw the shaft into the bottom of the oiler pump more than 15 turns as this may not allow for proper lubrication of the roller chains.

IMPORTANT! Always use new 30 weight oil. In cold weather, use a SAE 10 or a mixture of two parts of 30 weight oil to one part diesel fuel.

Model 7200

-52-

Page 51 Page 53
Image 52
Page 51 Page 53
Contents Manufactured by 12/03Table of Contents MANUFACTURER’S Warranty VIIRemember Farm Equipment Buyers Trust the Name Meyer IntroductionModel No Serial No Date of Purchase Safety Precautions Safety First Industrial Series Gear Boxes Decal H. Part noTractor Drawbar & PTO Specification PRE-OPERATIONMaterial Estimated Weight PER Cubic Foot Maximum Spreader Load WeightsTransporting Tractor Towing Size RequirementsOptional Truck Mount Spreaders USE of Safety ChainFreezing Weather Operation Model Loading OperationUnloading Shear Sprocket Instructions DescriptionStorage After USE PTO Setup Adjustment on the Cutout ClutchPTO Driveline Driveline AttachmentLubrication Maintenance InformationNormal Operation Adjustments Front Drive Roller ChainsThird Chain Drive Spring Loaded Material Guide Adjustment Shear ARM Material Guide AdjustmentSpinner Material Guides 1/2Daily Lubrication every 8-12 loads LubricationWeekly Lubrication every 25-30 loads Monthly Lubrication Repair Parts PTO Drive Shaft AssemblyKEY Meyer Part Description RPM-20 Spline / 1-3/4 Yoke WWE2480 80 Degree C.V KEY Description KEY Part no DescriptionAuger Drive Third Reduction This Page Intentionally Blank Front Shield & Side Shaft Drive KEY Description Auger Drive First Reduction RPM Auger Drive Second Reduction Auger Drive Second Reduction RH Auger Drive Final Reduction RH Auger Drive Final Reduction LH Auger Drive Final Reduction This Page Intentionally Blank BOX, Augers & Side Shaft KEY Description Unloading Gate and Gate Indicator Unloading Gate and Gate Indicator Spinners & Gearbox Shaft Drive Spinners & Gearbox Shaft Drive Spinner Gear Reducer Left Hand 11 #19-0029 Spinner Gear Reducer Center 11 #19-0030 KEY DescriptionCorner Gear Reducer Right Hand KEY RPM Drive Part no DescriptionHUBS, Axle & Tandem Assembly LADDER, Third AUGER, Gate Indicator & Lighting LADDER, Third AUGER, Gate Indicator & Lighting OIL-KIT KEY OEM Part no Description Instructions for Automatic Chain Oiler Meyer Industrial Spreader Trouble Shooting Symptom Problem Solution AugersMeyer Industrial Spreader Maintenance Record Date Service PerformedMeyer Equipment Wheel Torque Tire Inflation Tire Size PLY PSIThis Page Intentionally Blank Model Model Specifications Subject to Change Without Notice Meyer Industrial Spreader SpecificationsModel

7200 specifications

The Meyer 7200 is a cutting-edge agricultural tractor that stands out in the competitive landscape of modern farming equipment. Designed with efficiency and versatility in mind, it caters to the diverse needs of farmers and agricultural professionals. One of the primary features of the Meyer 7200 is its robust engine, which delivers remarkable power while maintaining fuel efficiency. With a maximum horsepower rating that exceeds expectations, this tractor is capable of handling a wide range of tasks, from plowing and tilling to hauling heavy loads.

The Meyer 7200 incorporates advanced technology that enhances its performance and usability. One notable technological feature is the integrated GPS guidance system, which assists farmers in optimizing field operations by providing precise navigation and mapping capabilities. This system not only minimizes overlaps during planting and spraying but also maximizes efficiency and productivity. The tractor is also equipped with an intuitive touchscreen interface, allowing operators to easily monitor performance metrics and adjust settings on-the-go.

Another significant characteristic of the Meyer 7200 is its exceptional maneuverability. The tractor is designed with a compact frame and a superior turning radius, making it adept at navigating tight corners and various terrains. This feature is particularly beneficial in smaller fields or crowded workspaces. Additionally, the tractor boasts an advanced suspension system that enhances ride comfort and stability, reducing operator fatigue during long hours in the field.

Durability is a hallmark of the Meyer 7200, with components built to withstand the rigors of daily farm work. The high-quality materials and robust construction ensure longevity and minimize maintenance requirements. Farmers can rely on the Meyer 7200 to perform reliably under heavy workloads, even in challenging weather conditions.

Safety is also a priority, with features such as roll-over protection structures and advanced braking systems. These safety enhancements provide peace of mind for operators, allowing them to focus on their tasks without added worry.

In summary, the Meyer 7200 is a powerful, efficient, and technologically advanced tractor that meets the demands of modern agriculture. With its powerful engine, integrated GPS system, exceptional maneuverability, durability, and safety features, the Meyer 7200 is an indispensable tool for farmers looking to elevate their productivity and ensure successful harvests. As the agricultural landscape continues to evolve, the Meyer 7200 stands ready to meet the challenges of today and tomorrow.
Top Page Image Contents