Meyer 7200 manual Lubrication, Normal Operation, Maintenance Information

Page 16

Adjust the drawbar at 16-20” above the ground. Extend or shorten the drawbar so horizontal distance from end of tractor PTO shaft to center of hitch pin hole is 16” for 1000 RPM 1-3/8-21 spline, (14” for 540 RPM 1-3/8-6 spline) (20” for 1000 RPM 1-3/4-20 spline). Secure the drawbar so the hitch pin hole is located directly below the PTO driveline. PTO adapters are not recommended as damage to the driveline may occur. A hitch pin with a minimum diameter of 1-5/16” and bottom retaining pin is recommended.

AN IMPROPERLY LOCATED HITCH POINT MAY CAUSE DAMAGE TO THE UNIVERSAL JOINTS OF THE PTO DRIVE SHAFT. CONFORMING TO THE STANDARD 16” DRAWBAR (1000 RPM) AND PTO RELATIONSHIP WILL ENSURE THAT THE PTO DRIVESHAFT WILL NOT BECOME OVER EX- TENDED. WITH INITIAL HOOK-UP TO YOUR NEW MEYER SPREADER TEST PTO TRAVEL BY TURNING EQUIPMENT IN BOTH DIRECTIONS OB- SERVING THE MINIMUM AND MAXIMUM TRAVEL DIMENSIONS AS SHOWN PER DRAWING ON FIG- URE 6.

LUBRICATION

LUBRICATION

A high quality Lithium Base Grease should be used

PRIOR TO USE

A.Using the CV Zerk (Key #2) place 20 pumps of grease into the CV center housing. This should be done with the driveline / CV as straight as possible.

B.Slowly articulate the double joint through its maximum joint angle several times.

C.Return the CV joint to its straight position and insert additional grease into the CV Zerk (Key #2) until grease is evident around the housing and center sliding disk.

NORMAL OPERATION

A.Lubricate the following items after every eight

(8)hours of operation. If short rows and frequent turning or other demanding conditions exist, lubricate at four (4) hour intervals.

1.Cross and bearings (Key #1)-Add grease until it is purged around the seals

2.CV center housing (Key #2)-Add grease until it is evident around the center sliding disk.

3.Telescoping members (Key #3)-Add grease until it adequately covers the sliding members. Take apart occasionally to make sure adequate lubrication is being added.

4.Shield bearings (Key #4)-Add 2-3 pumps.

FAILURE TO FREQUENTLY GREASE THE CV CENTER HOUSING AND TELESCOPING MEMBERS WILL REDUCE THE LIFE OF THE CV.

FIGURE 6. PTO DRIVELINE

MAINTENANCE INFORMATION

It is extremely important to follow the maintenance guidelines. If telescoping members become hard to slide during normal operation, it is recommended the shaft be taken apart, cleaned with solvent and recoated with grease before re-assembling. As a minimum it is important this be done after each season of use.

Model 7200

-16-

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Manufactured by 12/03Table of Contents MANUFACTURER’S Warranty VIIRemember Farm Equipment Buyers Trust the Name Meyer IntroductionModel No Serial No Date of Purchase Safety Precautions Safety First Industrial Series Gear Boxes Decal H. Part noTractor Drawbar & PTO Specification PRE-OPERATIONMaterial Estimated Weight PER Cubic Foot Maximum Spreader Load WeightsTransporting Tractor Towing Size RequirementsOptional Truck Mount Spreaders USE of Safety ChainFreezing Weather Operation Model Loading OperationUnloading Shear Sprocket Instructions DescriptionStorage After USE PTO Setup Adjustment on the Cutout ClutchPTO Driveline Driveline AttachmentLubrication Maintenance InformationNormal Operation Adjustments Front Drive Roller ChainsThird Chain Drive Spring Loaded Material Guide Adjustment Shear ARM Material Guide AdjustmentSpinner Material Guides 1/2Daily Lubrication every 8-12 loads LubricationWeekly Lubrication every 25-30 loads Monthly Lubrication Repair Parts PTO Drive Shaft AssemblyKEY Meyer Part Description RPM-20 Spline / 1-3/4 Yoke WWE2480 80 Degree C.V KEY Description KEY Part no DescriptionAuger Drive Third Reduction This Page Intentionally Blank Front Shield & Side Shaft Drive KEY Description Auger Drive First Reduction RPM Auger Drive Second Reduction Auger Drive Second Reduction RH Auger Drive Final Reduction RH Auger Drive Final Reduction LH Auger Drive Final Reduction This Page Intentionally Blank BOX, Augers & Side Shaft KEY Description Unloading Gate and Gate Indicator Unloading Gate and Gate Indicator Spinners & Gearbox Shaft Drive Spinners & Gearbox Shaft Drive Spinner Gear Reducer Left Hand 11 #19-0029 Spinner Gear Reducer Center 11 #19-0030 KEY DescriptionCorner Gear Reducer Right Hand KEY RPM Drive Part no DescriptionHUBS, Axle & Tandem Assembly LADDER, Third AUGER, Gate Indicator & Lighting LADDER, Third AUGER, Gate Indicator & Lighting OIL-KIT KEY OEM Part no Description Instructions for Automatic Chain Oiler Meyer Industrial Spreader Trouble Shooting Symptom Problem Solution AugersMeyer Industrial Spreader Maintenance Record Date Service PerformedMeyer Equipment Wheel Torque Tire Inflation Tire Size PLY PSIThis Page Intentionally Blank Model Model Specifications Subject to Change Without Notice Meyer Industrial Spreader SpecificationsModel

7200 specifications

The Meyer 7200 is a cutting-edge agricultural tractor that stands out in the competitive landscape of modern farming equipment. Designed with efficiency and versatility in mind, it caters to the diverse needs of farmers and agricultural professionals. One of the primary features of the Meyer 7200 is its robust engine, which delivers remarkable power while maintaining fuel efficiency. With a maximum horsepower rating that exceeds expectations, this tractor is capable of handling a wide range of tasks, from plowing and tilling to hauling heavy loads.

The Meyer 7200 incorporates advanced technology that enhances its performance and usability. One notable technological feature is the integrated GPS guidance system, which assists farmers in optimizing field operations by providing precise navigation and mapping capabilities. This system not only minimizes overlaps during planting and spraying but also maximizes efficiency and productivity. The tractor is also equipped with an intuitive touchscreen interface, allowing operators to easily monitor performance metrics and adjust settings on-the-go.

Another significant characteristic of the Meyer 7200 is its exceptional maneuverability. The tractor is designed with a compact frame and a superior turning radius, making it adept at navigating tight corners and various terrains. This feature is particularly beneficial in smaller fields or crowded workspaces. Additionally, the tractor boasts an advanced suspension system that enhances ride comfort and stability, reducing operator fatigue during long hours in the field.

Durability is a hallmark of the Meyer 7200, with components built to withstand the rigors of daily farm work. The high-quality materials and robust construction ensure longevity and minimize maintenance requirements. Farmers can rely on the Meyer 7200 to perform reliably under heavy workloads, even in challenging weather conditions.

Safety is also a priority, with features such as roll-over protection structures and advanced braking systems. These safety enhancements provide peace of mind for operators, allowing them to focus on their tasks without added worry.

In summary, the Meyer 7200 is a powerful, efficient, and technologically advanced tractor that meets the demands of modern agriculture. With its powerful engine, integrated GPS system, exceptional maneuverability, durability, and safety features, the Meyer 7200 is an indispensable tool for farmers looking to elevate their productivity and ensure successful harvests. As the agricultural landscape continues to evolve, the Meyer 7200 stands ready to meet the challenges of today and tomorrow.
Top Page Image Contents