Meade LXD55 instruction manual Method 2 Axis Alignment Using Autostar

Page 53

Motor at back of mount

Fig. 42: Method #2 Setup. (A) Optical Tube; (B) Dec. Motor; (C) Cradle Ring Lock Knobs; (D) Eyepiece.

Method 2: Axis Alignment Using Autostar

Perform this procedure during the daytime. You will need to have an unobstructed view of an easily sighted landmark, such as a light post. Use a low-power eyepiece, such as the supplied 26mm. This procedure assumes that you have some familiarity with Autostar's menu structure (you will need to locate the "Setup: Telescope" menu). If necessary, refer to AUTOSTAR'S MENUS, page 25.

Note: For best result, perform this procedure after you have trained the drive. See page 20.

1.Adjust the latitude T-handle screws (26, Fig. 1d) so that the latitude is set to 45° or higher. See Step #6, page 12, for information about setting the latitude controls.

2.Refer to Fig. 42 while performing this step. The Dec. motor (B) must be posi- tioned so that it is at the back of the mount. The optical tube (A) must be approximately horizontal (i.e., parallel with the horizon) and the counterweight shaft must be pointing straight down..

If using a Schmidt-Newtonian model, loosen the cradle ring locks knobs (C) and move the optical tube until the eyepiece (D) points downward as shown in the Fig. 42. Re-tighten the cradle ring locks.

If using a refractor model, use the diagonal assembly to rotate the eyepiece to a convenient viewing angle during testing. However, be careful that the diag- onal is placed flush against the focuser and tightened in place using the thumb- screws. It is important that the diagonal does not slip during the procedure.

3.Make sure that both the R.A. and Dec. locks (17 and 33, Fig. 1d) are tightened to a firm feel.

4.Turn on Autostar and go to "Setup: Telescope." Press ENTER.

5.Press one of the Scroll keys until "LXD 55 Adjust" displays and then press ENTER. A message displays that tells you to center a landmark. If the landmark is not visible in your eyepiece, lift and move the entire telescope and tripod assembly— try not to move the tube too far from the horizontal position (no more than 5° up or down), as described in Step #2. You may also use the fine azimuth controls (27, Fig. 1d) for side to side movement and the Autostar Up/Down Arrows for small adjustments to the declination axis.

6.Caution: Before pressing ENTER, step back from the telescope assembly, as the telescope will begin to rotate about two axes. When the landmark is centered (Step #5), press ENTER.

The telescope first moves 180° on the Dec. axis and then rotates 180° on the R.A. axis. Autostar displays "Slewing....".

When the telescope has completed the 180° slew, the telescope will be under the mount instead of over it. The counterweight shaft is now pointed upwards and the cradle adjustment screws (Fig. 40) are easily accessible.

7.Autostar again prompts you to center the landmark you have chosen in the eyepiece. Use the Arrow keys to center the object and then press ENTER.

8.The telescope moves again on the R.A. axis. Use the cradle screw adjustment mechanism on the bottom of the cradle to center the landmark in the eyepiece.

To adjust the cradle screws, use the supplied hex key to loosen the two outside screws. Then adjust the position of the landmark by tightening or loosening the center screw. Perform this adjustment on both sets of screws. When finished, retighten the outer screws. The axis is now aligned.

Note: This procedure maximizes the pointing accuracy of the telescope provid- ed the telescope is always placed on the mount in the same fashion. A mark made on the mount under the saddle will ensure this alignment is maintained.

53

Image 53
Contents Meade Instruments Corporation Page Contents 1 1% g f e Telescope Features$2% LXD55-SeriesYour Personal Window to the Universe Computer Control Panel see e LXD55 Tips Tour the Cosmos with Just the Push of a Button Autostar FeaturesFeatures Tip Telescope Assembly How to Assemble Your TelescopeAccessories Getting StartedViewfinder assembly Schmidt-Newtonian models Insert eyepiece into holder and tighten thumbscrews Balancing the TelescopeChoosing an Eyepiece Aligning the ViewfinderObserving by Moving the Telescope Manually Too Much Power?Slew Speeds Autostar Models Only Activate the Arrow Keys Autostar Models OnlyObserve the Moon Setting the Polar Home PositionTracking Objects 16bUsing Autostars GO to Capabilities Autostar Models Only Observe a Star using the Automatic Tracking FeatureInitializing Autostar Autostar Models Only Moving Through Autostar’s Menus Autostar Models OnlyTraining the Drive Autostar Models Only Go To Saturn Autostar Models Only Easy Alignment Autostar Models OnlyPlanet Saturn is over 800 million miles from the Earth Using the Guided Tour Autostar Models OnlyTo Calculate Sunset time Autostar Navigation ExerciseNavigating Autostar Entering Data into AutostarSelect Item Object Autostars MenusObject Menu MenusGlossary Menu Event MenuUtilities Menu LXD55-SeriesEnter Setup MenuObserving Considerations Setup Menu Daylight SAVING, Surf the Web To Edit a Site Adding Observing SitesTo Add a Site to the user-defined site list To GO to a user-entered object Using Autostar to Find Objects Not in the LibrariesTo Add a landmark to the database Observing SatellitesLandmarks To perform a Landmark Survey To Check on the Available MemoryTo Select a landmark from the database Few tips on photography with the LXD55-Seriestelescopes Photography10 f/4 Optional AccessoriesSeries 4000 Photo-Visual Page General Maintenance MaintenanceD e f g Page Defocused star images. Misaligned 1, 2, Aligned Inspecting the Optics Meade Customer Service4 Model SN-8, SN-8EC Specifications Specifications5 Model SN-6, SN-6EC Specifications 8 Model AR-6 Specifications 10 f/4 Model SN-10 Specifications9.3 Model AR-5, AR-5EC Specifications Autostar Dimensions 10 Model SC-8 SpecificationsAutostar Specifications Appendix a Celestial Coordinates Setting CirclesOne- and Two-Star Polar Alignment Locating the Celestial PoleOne-Star Polar Alignment Two-Star Polar AlignmentProcedure #1 To correct for attitude misalignment Axis Alignment ProcedurePolar Alignment Viewfinder Method 1 Manual AlignmentPosition a Procedure #2 To correct for elevation misalignmentTips Star ChartsMethod 2 Axis Alignment Using Autostar Latitude Chart for Major Cities of the World Appendix C Latitude ChartCity State/Prov./Country Latitude City Country LatitudeAppendix D EC Handbox Slew Speeds To move the telescope using the Electronic ControllerModes of Operation Tracking Rates Optional Autostar Computer Controller for LXD55 EC Users Changing the Polar ModeMounting the SC bracket and optical tube to the mount How to Attach the Optical Tube to the MountAutostar Glossary Appendix F Basic AstronomyObjects in Space MoonDeep-Sky Objects PlanetsFurther Study Page Meade Instruments Corporation