Meade MAX-ACF How to Drift Align Max Northern Hemisphere, Test your Collimation

Page 29

Note:

See:

http://www.astrocruise.com

/polarnew.htm

for a website dedicated to drift alignment of Meade telescopes. Site offers extensive tips from an experienced drift align specialist.

How to Drift Align Max (Northern Hemisphere)

Important Note: You will need a reticle to perform this procedure

1.Center your reticle on a bright star near the Eastern horizon.

2.Look through the reticle while pressing Autostar's right and left Arrow keys. This will slew the mount back and forth in the R.A. axis.

3.Loosen and rotate the reticle until one of the crosshairs matches the right-left path of the star as you press the Arrow keys. This crosshair is now on the R.A. axis. The other axis is therefore on the Dec. axis. Carefully secure the reticle in place (do not move the crosshairs).

4.Observe the bright star you have chosen. If, over time, it drifts off the R.A. axis, use the latitude adjustment knob to bring it back past center. Experience will teach you how much to move the alt knob. If the star drifts slowly, use only a small amount of correction; if it moves quickly, use a much larger amount of correction.

5.Use Autostar's up and down keys to bring the star back to center. Perform step 4 repeatedly until it does not drift on the Dec axis for a few minutes.

6.Next, center on a bright, Southern star. This star should be within 10° to 20° of the celestial equator.

7.If the star drifts above the RA axis, use the Azimuth adjustment knob to move the star to the right and down until the star is almost out of the field of view. If it drifts below the R.A. axis, use the Azimuth adjustment knob to move the star to the left and up.

8.Use Autostar arrow keys to center the star again. Repeat steps 7 and 8 until the star no longer drifts off the R.A. axis for a few minutes.

9.Go back and check the first star and see if it is drifting again. And then recheck the second star also. Keep repeating steps 4, 7 and 8, until there is no more drift in either of the stars you have chosen for a few minutes.

Your telescope is now drift aligned. Next, collimate your telescope.

Collimation

This collimation procedure is for Meade MAX-ACF models only. The optical collima- tion (alignment) of any astronomical telescope used for serious purposes is impor- tant, but in the case of the MAX-ACF design, such collimation is absolutely essential for good performance. Take special care to read and understand this section well so that your telescope will give you the best optical performance.

As part of final optical testing, every Meade MAX-ACF telescope is precisely colli- mated at the Meade factory before shipment. However, vibrations in shipping can cause the optical system to become misaligned. Re-aligning the optics is, however, a straightforward process with the MAX-ACF.

Test your Collimation

Before collimating an MAX-ACF model, you will need to test your collimation.

To test the collimation, center a bright star that is overhead, or use a “hot spot” of reflected Sunlight from a chrome car bumper, with the supplied 24mm eyepiece. Allow the telescope to adjust to the temperature of your observation site before proceeding; temperature differences between the optics and the outside air can cause distortion in the images. Autostar II offers two options in the Utilities menus that take tempera- ture readings: “OTA Temperature” (the temperature of the corrector plate) and “Ambient Temperature” (the temperature of the air around the fork arms).

When the star or hot spot is centered, de-focus the image. You will notice that the out of focus star image looks like a ring of light surrounding a dark central spot; the dark central spot is in fact the shadow of the secondary mirror. You may notice multiple rings; these are called diffraction rings. Focus until the diffraction rings fills about 10% of the eyepiece field-diameter. If the dark central spot is offset in (i.e., not concentric with) the diffraction rings, your telescope’s optical system is misaligned and requires collimation.

Looking at or near the Sun will cause irreversible damage to your eye. Do not point this telescope at or near the

29

Sun. Do not look through the telescope as it is moving.

 

Page 28 Page 30
Image 29
Page 28 Page 30
Contents MEADE.COM Page Contents Components of MAX Telescope FeaturesPedestal Assembly Pedestal Wedge AssemblyRight Ascension Housing Assembly RA AssemblyDeclination Housing Assembly DEC AssemblyCounterweights COUNTER- WeightsTripod MAX TripodMaleTHE OTA Optical Tube AssemblyControl Panels and Ports RA Assembly Control Panel Saddle Control PanelLibrary # of Objects Autostar II FeaturesTour the Cosmos with Just the Push of a Button Sun. Do not look through the telescope as it is moving Sun. Do not look through the telescope as it is moving Pedestal Assembly and Adjusting Latitude Position Tripod AssemblyIf you need to set for low range or high range Latitude AdjustmentAssembly Requires TWO People to Lift RA AssemblyDEC Saddle Assembly Attach Counterweight Assembly 21 B Attach Optical Tube to the DEC Saddle Attach LOW Latitude CounterweightsWhen end Align the Viewfinder with the OTA Electrical ConnectionsHome Position and Balancing the OTA To Balance the RA AssemblyBalance the DEC Axis This ProcedureAlign the Viewfinder Mounting and Focusing the Viewfinder for the First TimeGetting Started Focusing the Telescope To sync on a focus preset To select a previously defined focus presetSlew Speeds To exit the focus operation at any timeTo prepare your telescope for Automatic Alignment Aligning for the First TimeTest your Collimation How to Drift Align Max Northern HemisphereCollimation OTA align bolt. Misaligned 1, 2, Aligned Follow these steps for collimation of the optical systemParking the Scope Calibrate HomeTo Calculate Sunset time Basic AutostarAutostar II Navigation Exercise Navigating Autostar Example of Locating a menuAutostar IIs Menus To slew the telescope to catalog objects Object MenuUtilities Menu Event MenuGlossary Menu Enter Setup Menu Sun. Do not look through the telescope as it is moving Setup Menu Daylight SAVING, above Hot Button Menus To Edit a Site Adding Observing SitesTo Add a Site to the user-defined site list To GO to a user-entered object Creating User ObjectsIdentify Observing SatellitesDisplayed information Example BrowseInitialize Autostar Alternate Polar AlignmentsTwo-Star Polar Alignment Easy Polar AlignmentUpdate Menu Option Periodic Error CorrectionTrain Menu Option Erase Menu OptionMeade Series 4000 Eyepieces Optional AccessoriesRear cells of Meade Schmidt-Cassegrain models Deep Sky Imager Maintenance Telescope Specifications Meade Consumer Solutions Advanced Autostar II System SpecificationsAutostar II Handbox Specifications Latitude Chart for Major Cities of the World Appendix a Latitude ChartCity State/Prov./Country Latitude City Country LatitudeAppendix B the Moon To observe the Apollo 15 landing site using the Moon optionTraining IntroductionOperation Permanently Mounted Scopes UpdateOther Menus Options Save As and Load OffAppendix D How to Read the Latitude Scale Page Meade Limited Warranty
Top Page Image Contents