Meade MAX-ACF Permanently Mounted Scopes, Other Menus Options Save As and Load, Update, Off

Page 57

•Save your model, using a good, descriptive name, using the “Save As” menu. Upon completion of the training, Smart Mount is enabled and remains on until you choose “Off” from the Smart Mount Configuration menu.

Permanently Mounted Scopes

For permanently mounted telescopes, it is not necessary to have more than one model unless the weight and balance of auxiliary equipment introduces balance or flexure changes that significantly affect pointing. The best practice is to train the Smart Mount and then run a couple of sessions with Update enabled. Thereafter, simply leave Smart Mount On as the installation default.

Other Menus Options

Save As and Load

The Smart Mount system allows you to save several models you have created (see TRAINING on the previous page) using the Save As command. Choose which model will be the "Current Model” using the Load command.

Update

The Update mode allows you to update training for the current model you have enabled. You will sync on several stars as previously described, which will further refine the pointing of your telescope. Save your model after running in update mode, otherwise the update will be lost when the telescope is powered off.

On

Load a model from memory (see SAVE AS AND LOAD above) and then Select Smart On. When Smart Mount is "On," the telescope will use the currently loaded model to refine your telescope's pointing, but will not update the model (see SMART MOUNT UPDATE above). If Smart Mount was "On" when you last powered off your telescope, it will be "On" when you start the next session.

Off

When Smart Mount is "Off," the telescope will not use any model you have created to refine pointing accuracy.

Erase

The Erase command clears the Current Smart Mount table values to allow a new model to be created.

Delete

The Delete command allows you to delete any model from memory. To delete a model, just scroll through the names and select the model to you wish to delete and press ENTER. You will be asked to confirm your choice. Press ENTER again and it will be removed from memory.

Looking at or near the Sun will cause irreversible damage to your eye. Do not point this telescope at or near the	57
Sun. Do not look through the telescope as it is moving.

Image 57

Contents MEADE.COM Page Contents Components of MAX Telescope FeaturesPedestal Assembly Pedestal Wedge AssemblyRight Ascension Housing Assembly RA AssemblyDeclination Housing Assembly DEC AssemblyCounterweights COUNTER- WeightsTripod MAX TripodMaleTHE OTA Optical Tube AssemblyControl Panels and Ports RA Assembly Control Panel Saddle Control PanelAutostar II Features Tour the Cosmos with Just the Push of a ButtonLibrary # of Objects Sun. Do not look through the telescope as it is moving Sun. Do not look through the telescope as it is moving Pedestal Assembly and Adjusting Latitude Position Tripod AssemblyIf you need to set for low range or high range Latitude AdjustmentAssembly Requires TWO People to Lift RA AssemblyDEC Saddle Assembly Attach Counterweight Assembly 21 B Attach Optical Tube to the DEC Saddle Attach LOW Latitude CounterweightsWhen end Align the Viewfinder with the OTA Electrical ConnectionsHome Position and Balancing the OTA To Balance the RA AssemblyBalance the DEC Axis This ProcedureMounting and Focusing the Viewfinder for the First Time Getting StartedAlign the Viewfinder Focusing the Telescope To sync on a focus preset To select a previously defined focus presetSlew Speeds To exit the focus operation at any timeTo prepare your telescope for Automatic Alignment Aligning for the First TimeHow to Drift Align Max Northern Hemisphere CollimationTest your Collimation OTA align bolt. Misaligned 1, 2, Aligned Follow these steps for collimation of the optical systemParking the Scope Calibrate HomeBasic Autostar Autostar II Navigation ExerciseTo Calculate Sunset time Navigating Autostar Example of Locating a menuAutostar IIs Menus To slew the telescope to catalog objects Object MenuEvent Menu Glossary MenuUtilities Menu Enter Setup Menu Sun. Do not look through the telescope as it is moving Setup Menu Daylight SAVING, above Hot Button Menus Adding Observing Sites To Add a Site to the user-defined site listTo Edit a Site To GO to a user-entered object Creating User ObjectsIdentify Observing SatellitesDisplayed information Example BrowseInitialize Autostar Alternate Polar AlignmentsTwo-Star Polar Alignment Easy Polar AlignmentUpdate Menu Option Periodic Error CorrectionTrain Menu Option Erase Menu OptionMeade Series 4000 Eyepieces Optional AccessoriesRear cells of Meade Schmidt-Cassegrain models Deep Sky Imager Maintenance Telescope Specifications Advanced Autostar II System Specifications Autostar II Handbox SpecificationsMeade Consumer Solutions Latitude Chart for Major Cities of the World Appendix a Latitude ChartCity State/Prov./Country Latitude City Country LatitudeAppendix B the Moon To observe the Apollo 15 landing site using the Moon optionIntroduction OperationTraining Permanently Mounted Scopes UpdateOther Menus Options Save As and Load OffAppendix D How to Read the Latitude Scale Page Meade Limited Warranty