Installation Wiring | Boston Acoustics 1005 manual

Installation - Wiring

Amplifier Fuses

Although the amplifier has internal fuses, additional fuse protection should be installed as close as possible to the battery on the positive (+) power wire going to the amplifier. An inline fuse should be installed at no more than 18" (46cm) on the positive (+) power wire. The rating of the inline fuse should equal the value of the internal fuse of the amplifier if only the single amplifier is connected to this wire. If other devices are connected to this wire, the fuse value should be of sufficient capacity to handle the demand.

Wire Gauge

The amplifier accepts up to 4-gauge stripped wire at the DC power and ground input terminals, and 4-gauge is recommended as a minimum. Wire runs should be kept to the minimum practical length.

Power 12v and Ground (GND) Connection

Strip approximately 5/8” (16mm) of insulation. The positive (+) power wire is installed into the amplifier terminal marked “12v”. The negative (–) wire is installed into the terminal marked “GND”. The ground wire should be as short as possible and connected directly to the chassis of the vehicle. Make sure that the chassis connection point is free of rust, grease, dirt, paint, and other materials that may insulate the ground wire from making proper connection. Tighten the 12v and GND terminals with the supplied 4mm hex wrench to secure the wire into the terminals. If the power wire must be routed through a drilled or existing hole, use a nylon panel grommet to prevent the insulation from fraying. Failure to do so could lead to an electrical short if the wire insula- tion is worn through and the power wire is shorted to ground.

Remote Input Connection

Connect the REMOTE trigger lead from the head unit to the amplifier using the 3mm hex wrench to tighten the connector on the power block of the amplifier. (refer to the diagram on page 3).

Speaker Output Connection

Prepare each wire by stripping approximately 5⁄8” (16mm) of insulation. The pos- itive (+) speaker wires are installed into the amplifier terminal marked “SPEAK- ER OUTPUT” / “+” (refer to the diagram on page 3). The negative (–) speaker wires are installed into the amplifier terminal marked “SPEAKER OUTPUT” / “-”. Tighten the “SPEAKER OUTPUT”, “+”, and “-” terminals with the supplied 2mm and 3mm hex wrenches to secure the wires into the terminals. If the speaker wires must be routed through a drilled or existing hole, use a nylon panel grommet to prevent fraying the wire insulation. Failure to do so could lead to an electrical short if the wire insulation is worn through and the speaker wires are shorted to ground.

WARNING! Front and Rear Speakers impedance must not fall below 2-ohms Stereo / 4-ohms Mono. Subwoofer impedance must not fall below 2-ohms.

Installation - Wiring

1005 specifications

Boston Acoustics 1005 is a highly regarded speaker system that has garnered attention for its superior sound quality and innovative design. Known for its exceptional audio performance, the 1005 stands as a testament to Boston Acoustics' commitment to producing high-fidelity audio products.

One of the main features of the Boston Acoustics 1005 is its compact design, which allows it to fit seamlessly into various home environments without sacrificing sound quality. This sleek speaker is engineered to deliver powerful bass, detailed midrange, and crisp highs, making it a suitable choice for music enthusiasts and home theater systems alike.

The 1005 utilizes advanced driver technology, including premium woofers and tweeters that ensure a wide frequency response. The woofers are designed to recreate deep bass tones with clarity, while the tweeters provide a smooth high-frequency performance. This combination results in a balanced sound profile that can easily fill a room, allowing listeners to enjoy their favorite music and movies with immersive audio.

Another notable feature of the Boston Acoustics 1005 is its versatility. The speaker can be used in a variety of applications, from bookshelf setups to part of a larger surround sound system. This flexibility makes it an excellent choice for audiophiles looking to enhance their listening experience, whether they are watching films or enjoying music.

In terms of design, the Boston Acoustics 1005 exhibits a modern aesthetic that can complement various décor styles. The stylish cabinet construction not only adds visual appeal but also minimizes resonance, ensuring that unwanted vibrations do not interfere with sound quality.

Furthermore, Boston Acoustics has incorporated advanced acoustic technologies in the 1005 to enhance performance. These include precision tuning and optimization protocols that are aimed at maximizing speaker efficiency and minimizing distortion. This attention to detail ensures that the 1005 delivers accurate sound reproduction across different genres of music.

Overall, Boston Acoustics 1005 stands out in the competitive speaker market due to its combination of compact design, advanced audio technologies, and versatile application. With its outstanding sound quality and sleek aesthetics, it provides an enriching audio experience suitable for home use, making it a worthy investment for anyone looking to upgrade their sound system.