ViewSonic PJD5221, PJD5231, PJD5211, PJD5122, VS13305, VS13306, VS13308, VS13304 warranty Maintenance

Page 50

5.Pull out the lamp connector from a slot in the lamp compartment. Disconnect it from the projector as illustrated.

2

1 2

6.Lift the handle so that it stands up. Use the handle to slowly pull the lamp out of the projector.

CAUTION

•Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.

•Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.

•Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.

7.Insert the new lamp into the lamp compartment and make sure it fits in the projector.

8.Reconnect the lamp connector and place it back into its slot to be flush with the projector.

Maintenance 47

Page 49 Page 51
Image 50
Page 49 Page 51
Contents ViewSonic Compliance Information Lead Pb Mercury Hg Cadmium Cd SubstanceActual Concentration Hexavalent Chromium Cr6+ Polybrominated biphenyls PBBCopyright Information Table of contents Safety Instructions Important safety instructionsSafety instructions for ceiling mounting of the projector Introduction Projector featuresIntroduction Shipping contents Projector exterior view Projector and remote control Controls and functionsVolume keys + Lamp indicator lightColor Mode AutoRemote control effective range Pull out the battery holderPositioning your projector Choosing a locationProjection dimensions Screen Center of lensConnection Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerMonitor Computer VGA to DVI Cable VGA cable Connecting a monitorTo connect the projector to a monitor Best video quality Connecting Video source devicesConnecting audio Better video qualityConnecting a Component Video source device To connect the projector to a Component Video source deviceAV device Speakers Audio cable Video cable Cable Connecting an S-Video source deviceTo connect the projector to an S-Video source device Speakers AV device Video cable Audio cable Cable Connecting a composite Video source deviceTo connect the projector to a composite Video source device Operation OperationStarting up the projector See Timing chart on page 52 for details System Setup Basic Using the menusUse / to highlight the System Setup Basic menu System Setup AdvancedIf you forget the password Utilizing the password functionSetting a password New passwordDisabling the password function Entering the password recall procedureChanging the password Switching input signal Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Correcting keystoneMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio PC input signals D-Sub / Comp /2 analog RGB Selecting a picture modePicture modes for different types of signals Video input signals S-Video, Video, D-Sub / Comp /2 YPbPrSetting the User 1/User 2 mode Using Screen ColorFine-tuning the image quality in user modes Adjusting BrightnessAdjusting Sharpness Adjusting ColorAdjusting Tint Adjusting Brilliant ColorTo adjust the settings Color ManagementOrder to draw the audiences full attention to Hiding the imageLocking control keys Operating in a high altitude environment To activate the High Altitude ModeFreezing the image Press MENU/EXIT on the projector or MenuPersonalizing the projector menu display Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system Basic AdvancedDescription of each menu Reference Color ModeSettings ModeTimer Auto PowerBlank Timer ProjectorAudio System Setup Advanced menu Function Description Active VGAOut MenuSecurity Advanced Settings Reset AllLamp CurrentMaintenance Care of the projectorLamp information Setting Lamp mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageLoosen the screw that secures the lamp Replacing the lampType number RLC-055 PJD5122/PJD5211/PJD5221 RLC-056 PJD5231 Maintenance Restart the projector Resetting the lamp timerTighten the screw that secures the lamp Light Status & Description IndicatorsPower events Lamp eventsTroubleshooting Cause RemedySpecifications Projector specificationsTiming chart DimensionsCeiling mount installation Signal Format Horizontal Frequency kHz HorizontalCopyright information Copyright informationIR control table RS232 command tableAppendix Pin assignment for this two endBaud Rate InterfaceRS-232 protocol Data Length Bit Parity Check None Stop BitContrast Write Blank on 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 VGA Hour Customer Support Limited Warranty How to get service PRJLW01 Rev hMexico Limited Warranty Viewsonic ProjectorNúmero Gratis DE Asistencia Técnica Para Todo México

PJD5211, VS13304, VS13306, PJD5221, VS13305 specifications

The ViewSonic PJD5122, VS13308, PJD5231, VS13305, and PJD5221 are part of ViewSonic's well-regarded projector lineup, designed to cater to various projection needs. These models provide high-quality imaging, portability, and user-friendly features that make them suitable for both educational and business environments.

The ViewSonic PJD5122 is a DLP projector that boasts a native SVGA resolution of 800x600, delivering clear images with vibrant colors and a brightness of 2,600 lumens. It employs DynamicEco technology, which enables users to save energy and extend lamp life by automatically lowering brightness when the projector is not in use. Enhanced connectivity options, including HDMI, VGA, and composite inputs, make it versatile for various devices.

The VS13308 model stands out with its compact design and lightweight build, making it easy to transport. With a brightness of 3,000 lumens and a native resolution of 800x600, it excels in both dim and well-lit environments. The projector features an impressive contrast ratio, ensuring rich, dark blacks for a more dynamic viewing experience. Its long lamp life of up to 10,000 hours means reduced maintenance costs.

The PJD5231 offers a native XGA resolution of 1024x768 and a brightness of 3,000 lumens, making it ideal for classrooms and conference rooms. This model utilizes a 3D-ready capability, providing an immersive viewing experience for 3D content. Users can easily connect multiple devices through its extensive input options, including VGA and composite, enhancing its flexibility.

The VS13305 model is engineered for versatility, with a brightness of 3,200 lumens and a native resolution of 800x600. It includes features like Energy-saving mode, which decreases power consumption and extends the life of the lamp. Its lightweight design makes it suitable for mobile professionals who require seamless portability.

Lastly, the PJD5221 also offers a native XGA resolution, combined with a brightness of 3,200 lumens, ensuring crisp details even in large rooms. The projector also supports a wide range of connection options and is equipped with built-in speakers, allowing for an all-in-one entertainment solution.

Together, these projectors highlight ViewSonic's commitment to delivering innovative display solutions with cutting-edge technologies, making them reliable choices for those in need of quality projection for various applications.
Top Page Image Contents