ViewSonic PJD5122, PJD5231 Resetting the lamp timer, Tighten the screw that secures the lamp

Page 51
Notice
Reset Lamp Timer?

9.Tighten the screw that secures the lamp.

CAUTION

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw.

10.Ensure the handle is fully laid flat and locked in place.

11.Replace the lamp cover on the

projector.

12.Tighten the screws that secure the lamp

cover.

CAUTION

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screws.

13.Restart the projector.

CAUTION

Do not turn the power on with the lamp cover removed.

Resetting the lamp timer

14. After the startup logo, open the On-Screen Display (OSD) menu. Go to the SYSTEM SETUP: Advanced > Lamp Settings menu.

Press MODE/ENTER on the projector or EnterReset Cancel on the remote control. The Lamp Settings page

is displayed. Press to highlight Reset lamp timer and press MODE/ENTER on the projector or Enter on the remote control. A warning message is displayed asking if you want to reset

the lamp timer. Highlight Reset and press MODE/ENTER on the projector or Enter on the remote control. The lamp time will be reset to '0'.

CAUTION

Do not reset if the lamp is not new or replaced as this could cause damage.

48 Maintenance

Page 50 Page 52
Image 51
Page 50 Page 52
Contents ViewSonic Compliance Information Hexavalent Chromium Cr6+ Polybrominated biphenyls PBB SubstanceActual Concentration Lead Pb Mercury Hg Cadmium CdCopyright Information Table of contents Important safety instructions Safety InstructionsSafety instructions for ceiling mounting of the projector Projector features IntroductionIntroduction Shipping contents Projector exterior view Controls and functions Projector and remote controlAuto Lamp indicator lightColor Mode Volume keys +Pull out the battery holder Remote control effective rangeChoosing a location Positioning your projectorScreen Center of lens Projection dimensionsTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionConnecting a monitor To connect the projector to a monitorMonitor Computer VGA to DVI Cable VGA cable Better video quality Connecting Video source devicesConnecting audio Best video qualityTo connect the projector to a Component Video source device Connecting a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceAV device Speakers Audio cable Video cable Cable Connecting a composite Video source device To connect the projector to a composite Video source deviceSpeakers AV device Video cable Audio cable Cable Operation Starting up the projectorOperation See Timing chart on page 52 for details System Setup Advanced Using the menusUse / to highlight the System Setup Basic menu System Setup BasicNew password Utilizing the password functionSetting a password If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Switching input signal Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Correcting keystone Fine-tuning the image size and claritySelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Video input signals S-Video, Video, D-Sub / Comp /2 YPbPr Selecting a picture modePicture modes for different types of signals PC input signals D-Sub / Comp /2 analog RGBAdjusting Brightness Using Screen ColorFine-tuning the image quality in user modes Setting the User 1/User 2 modeAdjusting Brilliant Color Adjusting ColorAdjusting Tint Adjusting SharpnessColor Management To adjust the settingsHiding the image Locking control keysOrder to draw the audiences full attention to Press MENU/EXIT on the projector or Menu To activate the High Altitude ModeFreezing the image Operating in a high altitude environmentShutting down the projector Personalizing the projector menu displayMenu operation Menu systemMain menu Sub-menu Options Advanced BasicDescription of each menu Mode Color ModeSettings ReferenceProjector Auto PowerBlank Timer TimerMenu System Setup Advanced menu Function Description Active VGAOut AudioCurrent Advanced Settings Reset AllLamp SecurityCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Type number RLC-055 PJD5122/PJD5211/PJD5221 RLC-056 PJD5231Loosen the screw that secures the lamp Maintenance Resetting the lamp timer Tighten the screw that secures the lampRestart the projector Lamp events IndicatorsPower events Light Status & DescriptionCause Remedy TroubleshootingProjector specifications SpecificationsDimensions Ceiling mount installationTiming chart Horizontal Signal Format Horizontal Frequency kHzCopyright information Copyright informationPin assignment for this two end RS232 command tableAppendix IR control tableData Length Bit Parity Check None Stop Bit InterfaceRS-232 protocol Baud RateContrast Write Blank on 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 VGA Hour Customer Support Limited Warranty PRJLW01 Rev h How to get serviceViewsonic Projector Mexico Limited WarrantyNúmero Gratis DE Asistencia Técnica Para Todo México

PJD5211, VS13304, VS13306, PJD5221, VS13305 specifications

The ViewSonic PJD5122, VS13308, PJD5231, VS13305, and PJD5221 are part of ViewSonic's well-regarded projector lineup, designed to cater to various projection needs. These models provide high-quality imaging, portability, and user-friendly features that make them suitable for both educational and business environments.

The ViewSonic PJD5122 is a DLP projector that boasts a native SVGA resolution of 800x600, delivering clear images with vibrant colors and a brightness of 2,600 lumens. It employs DynamicEco technology, which enables users to save energy and extend lamp life by automatically lowering brightness when the projector is not in use. Enhanced connectivity options, including HDMI, VGA, and composite inputs, make it versatile for various devices.

The VS13308 model stands out with its compact design and lightweight build, making it easy to transport. With a brightness of 3,000 lumens and a native resolution of 800x600, it excels in both dim and well-lit environments. The projector features an impressive contrast ratio, ensuring rich, dark blacks for a more dynamic viewing experience. Its long lamp life of up to 10,000 hours means reduced maintenance costs.

The PJD5231 offers a native XGA resolution of 1024x768 and a brightness of 3,000 lumens, making it ideal for classrooms and conference rooms. This model utilizes a 3D-ready capability, providing an immersive viewing experience for 3D content. Users can easily connect multiple devices through its extensive input options, including VGA and composite, enhancing its flexibility.

The VS13305 model is engineered for versatility, with a brightness of 3,200 lumens and a native resolution of 800x600. It includes features like Energy-saving mode, which decreases power consumption and extends the life of the lamp. Its lightweight design makes it suitable for mobile professionals who require seamless portability.

Lastly, the PJD5221 also offers a native XGA resolution, combined with a brightness of 3,200 lumens, ensuring crisp details even in large rooms. The projector also supports a wide range of connection options and is equipped with built-in speakers, allowing for an all-in-one entertainment solution.

Together, these projectors highlight ViewSonic's commitment to delivering innovative display solutions with cutting-edge technologies, making them reliable choices for those in need of quality projection for various applications.
Top Page Image Contents