Eiki EIP-WX5000L specifications Setting up the Projector Network Environment

Page 23

Setting up the Projector Network Environment

5 Click “Internet Protocol Version

4 (TCP/IPv4)”, and click the “Properties” button.

1

2

6 Confirm or change an IP address for the setup computer.

1Confirm and note the current IP ad- dress, Subnet mask and Default gateway.

Make sure to note the current IP ad- dress, Subnet mask and Default gate-

way as you will be required to reset them later.

2Set temporarily as follows :

IP address : 192.168.150.3

Subnet mask : 255.255.255.0

Default gateway : (Do not input any values.)

Note

•The factory default settings (“DHCP Client” is set to “OFF” on the projector) are as follows: IP address : 192.168.150.2

Subnet mask : 255.255.255.0

Default gateway : 0.0.0.0

7 After setting, click the “OK” but- ton, and then restart the computer.

After confirming or setting, proceed to “3. Setting up Network Connection for the Pro- jector”.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Setup Manual Standard Setup Front Projection Setting up the ScreenThrow Distance Screen Size and Projection DistanceF2.5, f=25.5-32 mm Signal Input Normal ModeF2.5, f=11.6 mm Fixed Wide Lens AH-55201F2.5, f=17.1 mm Fixed Wide Lens AH-55301F2.5, f=21.2-25.8 mm Wide-zoom Lens AH-55401F2.5, f=31.9-42.5 mm Tele-zoom Lens AH-55601F2.5, f=40.8-62.8 mm Tele-zoom Lens AH-55701F2.5, f=62.1-97.8 mm Tele-zoom Lens AH-55801Pin female connector Connecting Pin AssignmentsConnecting Pin Assignments Function and transmission codes Wired Remote Control Terminal SpecificationsSpecifications of wired remote control input Eiki remote control signal formatBasic format RS-232C Specifications and CommandsComputer control Communication conditions W R CommandsReturn PC RGB FAO CLR Temp Parameter 4500K 5500K 6500K Network settings on the computer Setting up the Projector Network EnvironmentConnecting the Pro- jector to a Computer Click Properties Setting an IP Address for the ComputerSetting up the Projector Network Environment Setting up a Network Connection for the Projector DNS Controlling the Projector via LAN Controlling the Projector Using Internet ExplorerControlling the Projector Confirming the ProjectorSetting the Security Setting and AdjustingSetting for Sending E-mail when an Error Occurs Making General Settings for the Network NetworkMail Recipient Settings InputPJS11234and press theEn- ter key Setting the Projector Using RS-232C or TelnetWhen Connecting Using RS-232C Input setup and press the Enter keyClickstartfrom theWindows desk- top and select Run When Connecting Using TelnetAdvanced Setup Menu Setup Menu Main MenuSet Items View Setting Detail ListVView All Setting Tings QQuit Unchanged Save Settings and QuitQuit without Saving Set SSave & QuitUser Name Setting IP Address SettingDefault Gateway Setting Subnet Mask SettingRS-232C Baud Rate Set Password SettingProjector Name Setting Dhcp Client SettingData Port Setting Disconnecting All ConnecSetting Auto Logout Time Entering Advanced Setup MenuAccepting All IP Addresses Setting of Accept IP Ad- dressCarrying out Network Ping Test Return to Main Menu Setting of Search PortReturn to Default Settings Stack Projection Turn off the both projectors Setting up the Stack ProjectionProjector 1 Master Projector 2 SlaveProjector Slave Projector MasterVideo Wall Projection Projector Setting up the Video Wall Projection BasicClick Video Wall on the menu Access one of the four projectors via Internet ExplorerSelect 1 X 1 on Division Click the assigning button Adjusting the Position Horizontally and VerticallyReturning to the Default Video Wall Setup Assigning the Projected Image on the Video Wall SetupVideo Wall Projection Setting up the Video Wall Projection Application Jectors as shown below Change the TCP/IP settings for the computer as shown belowMake the IP address for each pro- jector as shown below Click Stack on the menu Select Master on Stack SettingClick Stack on the menu Select Slave on Stack Setting Repeat the same procedure from the to 12 for the projector 3 Resetting the Lamp Timer of the Projector via LAN Close HyperTerminal Resetting the Lamp Timer of the Projector via LANWhen connecting the projector using serial-connection TroubleshootingTroubleshooting \ After the initialization, carry out setting again Units inches mm DimensionsWhen AH-55501 is installed When AH-55201 is installedWhen AH-55301 is installed When AH-55401 is installed

EIP-WX5000, EIP-WX5000L specifications

The Eiki EIP-WX5000 and EIP-WX5000L are cutting-edge projectors designed for high-performance presentations and immersive viewing experiences. Both models are equipped with advanced technologies that cater to the needs of professional environments, such as conference rooms, lecture halls, and large venues.

One of the standout features of the EIP-WX5000 series is its high brightness capability, with a luminosity of up to 5000 lumens. This ensures that images remain vibrant and visible even in well-lit environments, making it ideal for business presentations or educational settings where lighting conditions can vary. The WXGA resolution (1280 x 800 pixels) offers a sharp and clear image quality, enhancing the details and clarity of presentations and videos alike.

Both projectors leverage DLP technology, known for its durability and exceptional color accuracy. This technology enables a richer color palette and minimizes the risk of color decay over time, ensuring that users can rely on consistent performance. The EIP-WX5000 and EIP-WX5000L also feature a contrast ratio of up to 3000:1, providing deeper blacks and brighter whites, which accentuates the depth of the projected image.

Flexibility in installation is another appealing characteristic of these projectors. They come with a variety of lens options that support short throw, long throw, and ultra-short throw configurations. This adaptability makes them suitable for different room layouts and sizes, allowing users to set up the projector in a way that best suits their space.

Connectivity is a key component in today’s technology, and the EIP-WX5000 series does not disappoint. The projectors are equipped with multiple input options including HDMI, VGA, and USB, facilitating easy connections with a wide range of devices such as laptops, tablets, and Blu-ray players. The inclusion of built-in networking capabilities also allows for remote management and control via a web browser, enhancing convenience for IT departments.

For those concerned about noise levels, both models operate quietly, making them suitable for environments where distractions must be minimized. Additionally, they offer extensive lamp life, which contributes to lower maintenance costs over time.

In conclusion, the Eiki EIP-WX5000 and EIP-WX5000L projectors are engineered for excellence in presentation quality, adaptability, and ease of use, making them highly favorable for professional applications across various industries.
Top Page Image Contents