Eiki LC-NB3S owner manual Appendix Lamp Replacement, Lamp Replace Counter

Page 39

APPENDIX

LAMP REPLACEMENT

When the life of Projection Lamp of this projector draws to an end, LAMP REPLACEMENT indicator lights yellow. When a projected image becomes dark or the color of an image becomes unnatural, replacement of Projection Lamp is required.

 

 

 

 

 

 

 

 

 

 

 

 

CAUTION

 

 

 

CAUTION

 

 

 

 

For continued safety, replace with a lamp

 

 

 

Do not drop a lamp assembly or touch a glass

 

 

 

 

assembly of the same type.

 

 

 

bulb! The glass can shatter and may cause

 

 

 

 

Allow a projector to cool for at least 45

 

 

 

injury.

 

 

 

 

minutes before you open Lamp Cover. The

 

 

 

 

 

 

 

 

 

 

 

 

 

inside of a projector can become very hot.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Follow these steps to replace the lamp assembly.

LAMP COVER

1

Turn off the projector and disconnect AC plug. Allow the

 

projector to cool for at least 45 minutes.

2

3

Remove a screw with a screwdriver to remove Lamp Cover.

Remove 3 screws with a screwdriver and pull out Lamp Assembly by grasping Handle.

4

Replace Lamp Assembly with a new one and tighten 3 screws

LAMP

HANDLE

 

back. Make sure that Lamp Assembly is set properly. Replace

 

Lamp Cover and tighten a screw.

ASSEMBLY

 

5

6

Connect AC Power Cord to the projector and turn it on.

Reset Lamp Replace Counter (refer to the section “Lamp Replace Counter” below).

NOTE : Do not reset Lamp Replace Counter when Projection

Lamp is not replaced.

ORDER REPLACEMENT LAMP

Replacement Lamp can be ordered through your dealer. When ordering Projection Lamp, give the following information to the dealer.

Model No. of your projector : LC-NB3S

Replacement Lamp Type No. : POA-LMP35

(Service Parts No. 610 293 2751)

LAMP REPLACE COUNTER

Be sure to reset Lamp Replace Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP REPLACE Indicator stops lighting.

1

Turn projector on, press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to

 

move a red frame pointer to SETTING Menu icon (refer to page 35, 36).

2

Press POINT DOWN button to move a red frame pointer to “Lamp counter reset” and then press SELECT button. The

 

message "Lamp replace counter reset?" is displayed. Move the pointer to [Yes] and then press SELECT button.

3

Another confirmation dialog box appears and select [Yes] to reset Lamp Replace Counter.

Do not reset Lamp Replace Counter except after Projection Lamp is replaced.

39

Image 39
Contents Model LC-NB3S To the Owner Voor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Compact Design Digital Zoom for Computer Features and DesignName of Each Part of Projector PreparationSETTING-UP Projector Connecting AC Power CordFor Continental Europe Preparation Positioning Projector Adjustable FeetPreparation Moving Projector Terminals of Projector Connecting ProjectorTerminals Projector Connecting to ComputerConnecting to Video Equipment Before Operation Operation of Remote ControlRemote Control Batteries Installation Power ON-OFF Button TOP Controls and IndicatorsHOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Guide Window Before Operation Menu BARTurning OFF Projector Basic OperationTurning on / OFF Projector Turning on ProjectorPicture Freeze Function Adjusting ScreenZoom Adjustment Keystone AdjustmentDirect Operation Sound AdjustmentTimer Function Basic Operation No Show FunctionAuto Computer InputSelecting Input Source Selecting Computer SystemComputer Input Compatible Computer Specifications FreqKHz Auto PC Adj PC AdjustmentAuto PC Adjustment PC Adjust MenuComputer Input Manual PC Adjustment Display area Display area HFull screen Image Select Menu Picture Image AdjustmentsImage Level Select Direct Image Level Select MenuImage Adjust Menu Computer Input Image Level AdjustmentScreen Menu Picture Screen AdjustmentVideo Input AV System Menu Component Video Selecting Video SystemAuto AV System Menu Video or S-VIDEOCinema Sharpness Video Input Image Level AdjustmentColor TintProvides image at a normal video aspect ratio of 4 Setting Setting MenuSetting Menu To change the code of Projector To change the code of the Remote Control UnitAppendix Operating Wireless MouseInstallation Operating Wireless MouseMaintenance AIR Filter Care and CleaningCleaning Projection Lens Lamp Replace Counter Appendix Lamp ReplacementTroubleshooting Function does not Remote Control UnitWireless Mouse Does not workOptional Parts Technical SpecificationsUSB Connector Series B Appendix Configurations of the TerminalsKey to better communications Canada