Eiki LC-HDT10 instruction manual Compliances, Federal Communication Commission Notice

Page 4

COMPLIANCES

Federal Communication Commission Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

CAUTION!

This is a Class A equipment. This equipment can cause interference in residential areas; in this case, the operator can be asked to take adequate countermeasures.

AC POWER CORD REQUIREMENT

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada :

AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA).

AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature.

Should you be unable to insert the plug into the outlet, contact your electrician.

GROUND

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

4

Image 4
Contents Model LC-HDT10 Multimedia ProjectorTo the Owner Safety Instructions Voor de klanten in NederlandCompliances Federal Communication Commission NoticeTable of Contents Features and Design ComputersColor Systems Component VideoPreparation Name of Each Part of ProjectorSETTING-UP Projector Connecting AC Power CordFor U.S.A. and Canada For Continental Europe 200 240 V ACLens Shift Adjustment Preparation Lens InstallationPositioning Projector Preparation Picture Level and Tilt Adjustment Moving ProjectorReplacement of Terminal Connecting ProjectorTerminals of Projector Connecting Projector INPUT/OUTPUT Terminals and Jacks Input Input 2Connecting Projector Serial Port TerminalConnecting to Computer Terminals ProjectorVideo Source example Before Operation Side Controls and IndicatorsSide Controls Indicators Front IndicatorsOperation of Remote Control 1WIRED Remote JackRemote Control Code Change and Operating Range Operating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR System BOXBasic Operation Turning on / OFF ProjectorTurning on Projector Turning OFF ProjectorAdjusting Screen Zoom AdjustmentFocus Adjustment Picture Freeze FunctionSound Adjustment Direct OperationMenu Operation Sound MenuSelecting Input Source Pb/Cb, Pr/CrRGBAnalog RGBScartSystem Select Automatic MULTI-SCAN SystemAuto System MenuBasic Operation Select Video System AutoSystem Select Menu SDI System Select Menu Component videoDisplay Adjust Display AdjustmentsScreen Adjustments Screen Adjustment DirectDisplay Adjust Auto PC Adjustment Auto PC AdjDisplay Adjust Manual Display Adjustments Current mode ClampImage Adjustments Image Adjust MenuImage Level Select Direct Image Level Select MenuDisplay Adjust Image Level Adjustments Noise reduction Progressive scanAuto picture control Auto lamp controlSetting Menu SettingSetting Menu Menu position LogoCeiling RearTo change the code of the Remote Control Unit Power managementRemote control To change the code of ProjectorLamp counter reset Factory defaultKey lock QuitMaintenance AIR Filter Care and CleaningIndicator AppendixAppendix Lamp Management Yellow Lamp Dim Lamp Red LampLamp Status Mark on LampAppendix Lamp Replacement Front Indicators Rear IndicatorsCleaning Projection Lens Order Replacement LampTroubleshooting Remote Control Unit ServiceDoes not work Indicators Projector Condition Appendix Indicators and Projector ConditionAppendix Menu Tree Input SystemImage adjust Technical Specifications Appendix Configurations of Terminals Pin ConfigurationAppendix Compatible Computer Specifications ResolutionOptional Parts HDB 15 pin-SCART 21 pin Cable Type NoTerminal Board Y/C Type No Terminal Board Faroudja Type NoKey to better communications Canada
Related manuals
Manual 52 pages 12.47 Kb