Eiki LC-XB26, LC-XB21 owner manual Remote Control Code, Remote Control Battery Installation

Page 14

Part Names and Functions

Remote Control Code

This projector has eight different remote control codes (Code 1-Code 8). Switching remote control codes prevents remote control interference when operating several projectors or video equipment at the same time. Change the remote control code for the projector first before changing that for the remote control. See “Remote control” in Setting on page 46.

1

With holding down the MENU button, press the IMAGE

 

button. The code switches sequentially for one pressing the

 

IMAGE button. (See the list below.)

2

To initialize the

remote control code, slide the

 

RESET/ON/ALL-OFF switch to RESET, and then to ON. The

 

initial code is Code 1. (p11)

 

 

 

 

 

 

Remote Control Code

 

Number of Times of

 

 

 

Pressing IMAGE Button

 

 

 

 

 

 

 

 

 

 

 

Code 1

 

1

 

 

 

 

 

 

 

Code 2

 

2

 

 

 

 

 

 

 

Code 3

 

3

 

 

 

 

 

 

 

Code 4

 

4

 

 

 

 

 

 

 

Code 5

 

5

 

 

 

 

 

 

 

Code 6

 

6

 

 

 

 

 

 

 

Code 7

 

7

 

 

 

 

 

 

 

Code 8

 

8

 

 

 

 

 

 

IMAGE button

While pressing the MENU button, press the IMAGE button number of times corresponding to the remote control code.

MENU button

Remote Control Battery Installation

1

Remove the battery

compartment lid.

Press the lid downward and slide it.

2

Slide the batteries into

3

Replace the compartment

the compartment.

lid.

Two AA size batteries For correct polarity (+ and

–), be sure battery terminals are in contact with pins in compartment.

To insure safe operation, please observe the following precautions :

Use (2) AA, UM3 or LR6 type alkaline batteries.

Replace two batteries at the same time.

Do not use a new battery with a used battery.

Avoid contact with water or liquid.

Do not expose the remote control to moisture, or heat.

Do not drop the remote control.

If a battery has leaked on remote control, carefully wipe case clean and install new batteries.

Risk of explosion if battery is replaced by an incorrect type.

Dispose of used batteries according to the instructions.

14

Image 14
Contents Model LC-XB26 LC-XB21 Features and Design Table of Contents To the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandMoving the Projector Installing the Projector in Proper PositionAir Circulation Compliance Federal Communication Commission NoticeBack Bottom Part Names and FunctionsFront Rear Terminal Part Names and FunctionsTop Control Remote Control @1 !3Laser Pointer Function Pointer FunctionPart Names Wireless Mouse OperationOperating Range FunctionsButton. The code switches sequentially for one pressing Remote Control CodeRemote Control Battery Installation With holding down the Menu button, press the ImagePositioning the Projector InstallationAdjustable Feet 200 240 V AC Connecting the AC Power CordFor the U.S.A. and Canada Connecting to a Computer InstallationConnecting to Video Equipment CableConnecting to Component Video Equipment Monitor OUTTurning On the Projector What is PIN code?Basic Operation Enter a PIN codeTurning Off the Projector Basic OperationOn-Screen Menu How to Operate the On-Screen MenuRemote Control Top ControlMenu Bar Basic OperationZoom and Focus Adjustment Auto Setup FunctionNo Show Function Keystone AdjustmentPicture Freeze Function BasicVolume Timer FunctionSound Adjustment MuteComputer Input Computer InputInput Source Selection Mode Computer System SelectionAuto PC System MenuTo store adjustment parameters Auto PC AdjustmentPC Adjust Menu Auto PC AdjManual PC Adjustment Display area ResetMode free Display area HImage Level Selection Image Level Adjustment Screen Size Adjustment Video Input Video InputInput Source Selection Video, S-Video Input button Video Computer Video buttonInput Source Selection Component, RGB Scart 21-Pin Input button Computer Video Computer buttonAV System Menu Video or S-Video Video System SelectionAuto AV System Menu ComponentImage button Dynamic Standard Cinema BlackboardGreen CinemaImage1~4 Color TintProgressive FilmProvides image at a normal video aspect ratio of 4 Auto Setup SettingSetting LanguageSetting Ceiling LogoCapture RearLamp mode Standby modePower management On startUSB Remote controlPointer Key lockTo Change the PIN Code To Change the PIN Code Lock settingPIN code lock Fan Factory default Lamp counter resetFactory default FanProjector is shut down and the Warning indicator lights red Maintenance and CleaningCleaning Then check the matters belowCleaning the Air Filters Attaching the Lens CoverMaintenance & Cleaning Cleaning the Projection LensCleaning the Projector Cabinet Lamp Replacement Reset the Lamp replace counterWhen the lamp replace counter is reset, the Lamp Lamp Replace CounterTroubleshooting AppendixComputer 2 cannot be selected Remote Control does not workAppendix Terminal item cannot be selectedMenu Tree System Setting Image SelectIndicators and Projector Condition Projector ConditionKHz Compatible Computer SpecificationsFreq Technical Specifications This cable is used for RGB Scart 21-Pin AccessoriesOptional Parts Video output of video equipmentTerminal HDB15-PIN Configurations of TerminalsUSB Connector Series B Terminal DVI-ILogo PIN Code Lock No PIN Code Number MemoPIN Code Lock No Key to better communications Canada