Eiki LC-XB26, LC-XB21 owner manual To the Owner, Risk of Electric Shock Do not Open

Page 4

To the Owner

Before operating this projector, read this manual thoroughly and operate the projector properly.

This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time.

Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.

If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the “Troubleshooting” section in the end of this booklet. If the problem still persists, contact the dealer where you purchased the projector or the service center.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER'S MANUAL WITH THIS UNIT.

Safety Precaution

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This projector produces intense light from the projection lens. Do not stare directly into the lens as possible. Eye damage could result. Be especially careful that children do not stare directly into the beam.

Install the projector in a proper position. If not, it may result in a fire hazard.

Provide appropriate space on the top, sides and rear of the projector cabinet for allowing air circulation and cooling the projector. Minimum clearance must be maintained. If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. Do not cover the ventilation slot on the projector. Heat build- up can reduce the service life of your projector, and can

also be dangerous.

SIDE and TOP

REAR

20cm

 

 

 

 

 

 

 

 

 

 

50cm

 

50cm

 

 

 

50cm

 

 

 

 

 

 

 

Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation holes.

If the projector is not to be used for an extended time, unplug the projector from the power outlet.

READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.

CAUTION

Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75.

Ne puet être utillisé dans une salle d’ordinateurs telle que définie dans la norme ANSI/NFPA 75 Standard for Protection of Electronic Computer/Data Processing Equipment

4

Image 4
Contents Model LC-XB26 LC-XB21 Features and Design Table of Contents To the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandAir Circulation Installing the Projector in Proper PositionMoving the Projector Compliance Federal Communication Commission NoticeFront Part Names and FunctionsBack Bottom Rear Terminal Part Names and FunctionsTop Control Remote Control @1 !3Laser Pointer Function Pointer FunctionWireless Mouse Operation Operating RangePart Names FunctionsRemote Control Code Remote Control Battery InstallationButton. The code switches sequentially for one pressing With holding down the Menu button, press the ImageAdjustable Feet InstallationPositioning the Projector For the U.S.A. and Canada Connecting the AC Power Cord200 240 V AC Connecting to a Computer InstallationConnecting to Video Equipment CableConnecting to Component Video Equipment Monitor OUTWhat is PIN code? Basic OperationTurning On the Projector Enter a PIN codeTurning Off the Projector Basic OperationHow to Operate the On-Screen Menu Remote ControlOn-Screen Menu Top ControlMenu Bar Basic OperationZoom and Focus Adjustment Auto Setup FunctionKeystone Adjustment Picture Freeze FunctionNo Show Function BasicTimer Function Sound AdjustmentVolume MuteInput Source Selection Computer InputComputer Input Computer System Selection AutoMode PC System MenuAuto PC Adjustment PC Adjust MenuTo store adjustment parameters Auto PC AdjManual PC Adjustment Reset Mode freeDisplay area Display area HImage Level Selection Image Level Adjustment Screen Size Adjustment Video Input Input Source Selection Video, S-VideoVideo Input Input button Video Computer Video buttonInput Source Selection Component, RGB Scart 21-Pin Input button Computer Video Computer buttonVideo System Selection AutoAV System Menu Video or S-Video AV System Menu ComponentImage1~4 CinemaImage button Dynamic Standard Cinema BlackboardGreen Color TintProgressive FilmProvides image at a normal video aspect ratio of 4 Setting SettingAuto Setup LanguageSetting Logo CaptureCeiling RearStandby mode Power managementLamp mode On startRemote control PointerUSB Key lockPIN code lock To Change the PIN Code Lock settingTo Change the PIN Code Lamp counter reset Factory defaultFan Factory default FanMaintenance and Cleaning CleaningProjector is shut down and the Warning indicator lights red Then check the matters belowCleaning the Air Filters Attaching the Lens CoverCleaning the Projector Cabinet Cleaning the Projection LensMaintenance & Cleaning Lamp Replacement Reset the Lamp replace counterWhen the lamp replace counter is reset, the Lamp Lamp Replace CounterTroubleshooting AppendixRemote Control does not work AppendixComputer 2 cannot be selected Terminal item cannot be selectedMenu Tree System Setting Image SelectIndicators and Projector Condition Projector ConditionFreq Compatible Computer SpecificationsKHz Technical Specifications Accessories Optional PartsThis cable is used for RGB Scart 21-Pin Video output of video equipmentConfigurations of Terminals USB Connector Series BTerminal HDB15-PIN Terminal DVI-IPIN Code Lock No PIN Code Number MemoLogo PIN Code Lock No Key to better communications Canada