Eiki LC-XB21, LC-XB26 owner manual Installation, Positioning the Projector, Adjustable Feet

Page 15

Installation

Positioning the Projector

This projector is designed to project on a flat projection surface and can be focused from 3.3’(1.0m) - 25.3’(7.7m). Refer to

the figure and the table below for the screen size and the distance between the projector and the screen.

Installation

A : B = 9 : 1

 

 

 

25.3' (7.7m)

 

 

 

300”

 

 

(Inch Diagonal)

 

16.4' (5.0m)

 

 

 

12.5' (3.8m)

Max. Zoom

 

 

195”

 

8.2' (2.5m)

195”

 

 

 

3.3' (1.0m)

150”

Min. Zoom

A

 

127”

100”

 

 

 

 

 

97”

 

 

40”

64”

 

 

 

 

 

 

 

 

(Center)

 

 

 

B

Screen Size

 

40”

 

100”

150”

195”

300”

(W x H) mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

813 x 610

 

2032 x 1524

3048 x 2286

3962 x 2972

6096 x 4572

4 : 3 aspect ratio

 

 

 

 

 

 

 

 

 

 

Zoom (min)

 

4.9' (1.5m)

 

12.8' (3.9m)

19.3' (5.9m)

25.3' (7.7m)

––-––

 

 

 

 

 

 

 

 

Zoom (max)

 

3.3' (1.0m)

 

8.2' (2.5m)

12.5' (3.8m)

16.4' (5.0m)

25.3' (7.7m)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note:

The brightness in a room has a great influence on picture quality. It is recommended to limit ambient lighting in order to obtain the best image.

The values shown above are approximate and may vary from the actual size.

Adjustable Feet

Projection angle can be adjusted up to 11.8 degrees with the adjustable feet.

1

Lift the front of the projector and pull upward the feet lock

 

latches on both sides of the projector.

2

Release the feet lock latches to lock the adjustable feet and

 

rotate the adjustable feet to adjust the position and tilt.

3

To retract the adjustable feet, lift the front of the projector

 

and pull and undo the feet lock latches.

Keystone distortion of the projected image can be adjusted automatically with Auto Setup function or manually with the remote control or the menu operation. (p24, 25, and 42)

Feet Lock Latches

Adjustable Feet

15

Image 15
Contents Model LC-XB26 LC-XB21 Features and Design Table of Contents Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsInstalling the Projector in Proper Position Air CirculationMoving the Projector Federal Communication Commission Notice CompliancePart Names and Functions FrontBack Bottom Part Names and Functions Rear TerminalTop Control @1 !3 Remote ControlPointer Function Laser Pointer FunctionFunctions Wireless Mouse OperationOperating Range Part NamesWith holding down the Menu button, press the Image Remote Control CodeRemote Control Battery Installation Button. The code switches sequentially for one pressingInstallation Adjustable FeetPositioning the Projector Connecting the AC Power Cord For the U.S.A. and Canada200 240 V AC Installation Connecting to a ComputerCable Connecting to Video EquipmentMonitor OUT Connecting to Component Video EquipmentEnter a PIN code What is PIN code?Basic Operation Turning On the ProjectorBasic Operation Turning Off the ProjectorTop Control How to Operate the On-Screen MenuRemote Control On-Screen MenuBasic Operation Menu BarAuto Setup Function Zoom and Focus AdjustmentBasic Keystone AdjustmentPicture Freeze Function No Show FunctionMute Timer FunctionSound Adjustment VolumeComputer Input Input Source SelectionComputer Input PC System Menu Computer System SelectionAuto ModeAuto PC Adj Auto PC AdjustmentPC Adjust Menu To store adjustment parametersManual PC Adjustment Display area H ResetMode free Display areaImage Level Selection Image Level Adjustment Screen Size Adjustment Input button Video Computer Video button Video InputInput Source Selection Video, S-Video Video InputInput button Computer Video Computer button Input Source Selection Component, RGB Scart 21-PinAV System Menu Component Video System SelectionAuto AV System Menu Video or S-VideoCinema Image1~4Image button Dynamic Standard Cinema BlackboardGreen Tint ColorFilm ProgressiveProvides image at a normal video aspect ratio of 4 Language SettingSetting Auto SetupSetting Rear LogoCapture CeilingOn start Standby modePower management Lamp modeKey lock Remote controlPointer USBTo Change the PIN Code Lock setting PIN code lockTo Change the PIN Code Fan Lamp counter resetFactory default Fan Factory defaultThen check the matters below Maintenance and CleaningCleaning Projector is shut down and the Warning indicator lights redAttaching the Lens Cover Cleaning the Air FiltersCleaning the Projection Lens Cleaning the Projector CabinetMaintenance & Cleaning Reset the Lamp replace counter Lamp ReplacementLamp Replace Counter When the lamp replace counter is reset, the LampAppendix TroubleshootingTerminal item cannot be selected Remote Control does not workAppendix Computer 2 cannot be selectedMenu Tree Image Select System SettingProjector Condition Indicators and Projector ConditionCompatible Computer Specifications FreqKHz Technical Specifications Video output of video equipment AccessoriesOptional Parts This cable is used for RGB Scart 21-PinTerminal DVI-I Configurations of TerminalsUSB Connector Series B Terminal HDB15-PINPIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Key to better communications Canada