Eiki LC-XG110 instruction manual Basic Operation, Turning on / OFF Projector, Turning on Projector

Page 19

BASIC OPERATION

TURNING ON / OFF PROJECTOR

TURNING ON PROJECTOR

1

Complete peripheral connections (with Computer, VCR, etc.)

before turning on projector. (Refer to "CONNECTING

 

PROJECTOR" on pages 11~13 for connecting the equipment.)

2

Connect the projector's AC Power Cord into an AC outlet. LAMP

Indicator lights RED, and READY Indicator lights GREEN.

 

NOTE : When “On start” function is ON, this projector is turned

 

on automatically by connecting AC Power Cord to an

 

AC outlet. (Refer to page 37.)

3

Press POWER ON-OFF button on Top Control or on Remote

Control Unit to ON. LAMP Indicator dims, and Cooling Fans

start to operate. Preparation Display appears on a screen and count-down starts. The signal from PC or Video source appears after 30 seconds.

Current Input position and Lamp mode status are also displayed on screen for 5 seconds. (Refer to "LAMP MODE" on page 37.)

Input position and

Lamp mode status

Computer 1

30

Preparation Display disappears after 30 seconds.

TURNING OFF PROJECTOR

1

Press POWER ON-OFF button on Top Control or on Remote

Control Unit, and a message "Power off?" appears on a screen.

2

Press POWER ON-OFF button again to turn off the projector.

LAMP Indicator lights bright and READY Indicator turns off.

 

After the projector is turned off, Cooling Fans operate (for 90

 

seconds). During this "Cooling Down" period, this appliance

 

cannot be turned on.

3

When projector has cooled down, READY Indicator lights

GREEN again and you can turn the projector on. After cooling

down completely, disconnect AC Power Cord.

TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF.

Power off?

Message disappears after 4 seconds.

When “Power Management” function is ON, projector detects signal interruption and turns off Projection Lamp automatically. Refer to “Power management” on pages 37.

When WARNING TEMP. indicator flashes red, projector is automatically turned off. Wait at least 5 minutes, conform READY indicator will light green and projector may be turned on by pressing POWER ON-OFF button.

When both WARNING TEMP. and READY indicators to flash, a projector cannot be turned on by pressing POWER ON-OFF button. In this case, follow procedures below:

1.Disconnect AC Power Cord from an AC outlet.

2.Turn a projector on again. (Refer to steps 2-3 of TURNING ON PROJECTOR on this page.)

When WARNING TEMP. indicator continues to flash, follow procedures below:

1.Disconnect AC Power Cord from an AC outlet.

2.Check Air Filters for dust accumulation.

3.Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 41.)

4.Turn a projector on again. (Refer to steps 2-3 of TURNING ON PROJECTOR on this page.)

If WARNING TEMP. indicator should still continue to flash, contact sales dealer where you purchased this projector or service center.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents
Multimedia Projector Model LC-XG110To the Owner Voor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Compact Design Features and DesignName of Each Part of Projector PreparationHOT AIR Exhausted Connecting AC Power Cord SETTING-UP ProjectorFor U.S.A. and Canada For Continental Europe Room Light Preparation Positioning ProjectorMoving Projector Preparation Adjustable FeetMonitor Output Connecting ProjectorTerminals of Projector Computer Input 2 DIGITAL/ANALOGTerminals Connecting to ComputerProjector Terminals Projector Connecting to Video EquipmentAudio Video Laser Pointer Function Operation of Remote ControlInside the Battery Compartment BOX Before OperationSelect Button Point Volume + ButtonsTimer Button Zoom ButtonLamp Replace Indicator TOP Controls and IndicatorsOperating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Guide Window Before Operation Menu BARSound Menu Turning OFF Projector Basic OperationTurning on / OFF Projector Turning on ProjectorKeystone Adjustment Adjusting ScreenZoom Adjustment Focus AdjustmentSound Adjustment RGB Scart Computer InputSelecting Input Source RGBAuto Selecting Computer SystemPC System Menu Resolution Computer Input Compatible Computer SpecificationsXGA Auto PC Adj PC AdjustmentAuto PC Adjustment PC Adjust MenuComputer Input Manual PC Adjustment Display area H Display areaFull screen Image 1~4 Picture Image AdjustmentsImage Level Select Direct Image Level Select MenuImage Adjust Menu Computer Input Image Level AdjustmentScreen Menu Picture Screen AdjustmentVideo Video InputVideo AV System Menu Video or S-VIDEO Component Video Signal FormatSelecting Video System PAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-NCinema Video Input Image Level Adjustment Provides image at a normal video aspect ratio of 4 Setting Menu SettingSetting Menu To change the code of Projector To change the code of the Remote Control UnitAppendix Lamp ReplacementLamp Replace Appendix Lamp Replace Counter Lamp Handling PrecautionsInstallation Operating Wireless MouseOperating Wireless Mouse Recommendation MaintenanceAIR Filter Care and Cleaning Cleaning Projection LensTroubleshooting Function does not Remote Control UnitWireless Mouse Does not workTechnical Specifications Computer INPUT-1 and Monitor OUT Terminals Analog Appendix Configurations of TerminalsControl Port Connector USB Connector Series BPOA-MACAP Appendix Optional PartsPOA-MCPS2 POA-MCMACAppendix Indicators and Projector Condition Indicators Projector ConditionKey to better communications Canada
Related manuals
Manual 48 pages 44.32 Kb