Eiki LC-X70 instruction manual Picture Image Adjustments, Image Adjust Menu

Page 34

PICTURE IMAGE

PICTURE IMAGE ADJUSTMENTS

1

Press MENU button and ON-SCREEN MENU will appear. Press

POINT LEFT/RIGHT buttons to move a red frame pointer to

 

IMAGE ADJUST Menu icon.

2

Press POINT UP/DOWN button to move a red frame pointer to

item that you want to adjust and then press SELECT button.

Level of each item is displayed. Adjust each level by pressing POINT LEFT/RIGHT button(s).

Contrast

Press POINT LEFT button to decrease contrast, and POINT RIGHT button to increase contrast. (From 0 to 63.)

Brightness

Press POINT LEFT button to adjust image darker, and POINT RIGHT button to adjust brighter. (From 0 to 63.)

Color

Press POINT LEFT button to lighten color, and POINT RIGHT button to deeper color. (From 0 to 63.)

Tint

Press POINT LEFT button or POINT RIGHT button to obtain proper color. (From 0 to 63.)

Color Management

The Color management function can be used to adjust the level, phase and gamma of the selected display colors on the screen, and to replace these colors with other colors if required.

The projector lets you replace up to eight colors for each image. There are four preset images for VIDEO mode and four preset images for PC, giving a total of eight images.

1

Press the POINT UP/DOWN button to move the red frame point-

er to "COLOR MANAGEMENT", and then press the SELECT

 

button. The COLOR MANAGEMENT menu will appear and

 

pointer mode will be enabled. The image that was being project-

 

ed when the button was pressed will be paused, and the COLOR

 

MANAGEMENT POINTER will appear.

2

Use the POINT buttons to move the pointer to a section of the

paused image that contains the color that you would like to

 

adjust, and then press the SELECT button. The mode will

 

change to COLOR SELECTION mode, and the color in the cen-

 

ter of the pointer will be selected and adjustment will be possi-

 

ble.

3

Use the POINT buttons to adjust the level and phase of the

color, and then press the SELECT button to confirm the setting.

Next, use the POINT buttons to adjust the gamma correction for the color, and then press the SELECT button to accept the set- ting. When the SELECT button is pressed, the mode will change to LIST mode.

IMAGE ADJUST MENU

IMAGE ADJUST

Menu icon

Move a red frame pointer to item to be selected and then press SELECT button.

Press POINT LEFT/RIGHT buttons to adjust value.

POINTER MODE

COLOR

MANAGEMENT

POINTER

NOTE;

Press the COLOR M. button on the remote con- trol to display the COLOR MANAGEMENT menu. If you would like to check or re-adjust a color management setting that has already been made, press the COLOR M. button on the remote control once more to change to LIST mode.

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Model LC-X70 Multimedia ProjectorTo the Owner Safety Instructions Voor de klanten in NederlandCompliances Esperanza Rancho Santa Margarita CATable of Contents Features and Design Compact Design Digital Zoom for ComputerName of Each Part of Projector PreparationHOT AIR Exhausted Connecting AC Power Cord SETTING-UP ProjectorFor U.S.A. and Canada For Continental Europe Preparation Positioning Projector Room LightPreparation Adjustable Feet Installing Projector in Proper PositionPreparation Moving Projector Connect computer output Digital DVI-D type to this terminal Connecting ProjectorTerminals of Projector Refer to P13A Projector Front of the projector Connecting to ComputerTerminals Audio Input External Audio Equipment Audio SpeakerConnecting to Video Equipment A ProjectorBefore Operation Operation of Remote ControlInside the Battery Compartment BOX Laser Pointer FunctionZoom Button Point Volume + ButtonsTimer Button Select ButtonTOP Controls and Indicators Point Volume + / ButtonsOperating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Press Menu Button while connecting to PC input sourceUsed to adjust picture image Used to selectTurning on Projector Basic OperationTurning on / OFF Projector Turning OFF ProjectorFocus adjustment may not function properly if the image is Adjusting ScreenKeystone Adjustment Corrected by Keystone adjustmentSound Adjustment Selecting Computer System Computer InputSelecting Input Source Rgbav HdcpAuto Automatic MULTI-SCAN SystemPC System Menu PC Adjust Menu PC AdjustmentAuto PC Adjustment Auto PC AdjComputer Input Manual PC Adjustment Display area H Display areaFull screen Image Level Select Menu Picture Image SelectImage Level Select Direct Image 1~4Picture Screen Adjustment Screen MenuVideo When video input signal is connected to Y-Pb/CbVideo Input Select VideoPAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N Component Video Signal FormatSelecting Video System AV System Menu Video or S-VIDEOPicture level adjusted for picture with fine tone CinemaProvides image at a normal video aspect ratio of 4 Provides image at a wide screen ratio of 16Image Adjust Menu Picture Image AdjustmentsPicture Image List Mode Picture ImageWhite balance Green Color tempWhite balance Red White balance BlueSetting Menu SettingSetting Menu Display AnamorphicBlue back Menu positionRemote control To change the code of the Remote Control UnitPower management To change the code of ProjectorProjector mode Wireless Mouse modeUSB Operating Wireless Mouse Operating Wireless MouseInstallation AppendixIndicatorIndicator MaintenanceSection AIR Filter Care and Cleaning on next Projector so that Ventilation Slots are not obstructedRecommendation Appendix AIR Filter Care and CleaningCleaning Projection Lens Pull up and removeLamp Replacement Lamp ReplaceAppendix Lamp Replace Counter Message Lamp replace counter reset? is displayed. MoveReset Lamp Replace Counter Pointer to Yes and then press Select buttonTroubleshooting Does not work Remote Control UnitWireless Mouse Function does notAppendix Indicators and Projector Condition Appendix Compatible Computer Specifications ResolutionMenu Tree PC sourceSystem Setting Sound Technical Specifications USB Connector Series B Appendix Configurations of TerminalsControl Port Connector Computer INPUT-1 and Monitor OUT Terminals AnalogLens Replacement Appendix Optional PartsAppendix Key to better communications Canada
Related manuals
Manual 56 pages 34.59 Kb

LC-X70 specifications

The Eiki LC-X70 is a high-performance multimedia projector designed for a variety of applications, including education, business, and large venues. Known for its versatility and advanced features, the LC-X70 offers exceptional image quality and user-friendly operation.

One of the standout features of the LC-X70 is its impressive brightness level, reaching up to 6,500 ANSI lumens. This high brightness capability makes it ideal for use in well-lit environments, ensuring that presentations maintain clarity and visibility. Coupled with a high contrast ratio, the projector delivers vivid colors and deep blacks, enhancing the overall viewing experience.

The LC-X70 utilizes advanced 3LCD technology, which ensures accurate color reproduction and reduces the risk of color fading over time. This technology enables the projector to produce images that are both bright and vibrant, making it suitable for projecting detailed graphics and videos. Furthermore, it supports resolutions up to WUXGA (1920 x 1200), allowing it to display high-definition content with stunning clarity.

Connectivity is another strong point for the Eiki LC-X70. It boasts a variety of input options, including HDMI, VGA, and USB ports, allowing users to connect multiple devices seamlessly. This flexibility makes it easy to integrate the projector into existing setups, whether in classrooms, conference rooms, or auditoriums. The inclusion of wireless connectivity options further enhances its usability, enabling users to project from laptops, tablets, and smartphones without the need for cables.

In addition to its impressive performance features, the LC-X70 is designed with user convenience in mind. It includes a user-friendly remote control, simplifying navigation through settings and options. The projector also features a built-in speaker, providing adequate audio output for presentations. For extended use cases, the projector is equipped with a long-lasting lamp, resulting in reduced maintenance costs.

In terms of portability, the Eiki LC-X70 is relatively compact and lightweight, making it easy to transport between locations. Its robust construction ensures durability, making it a reliable choice for users who require a projector that can withstand regular use.

Overall, the Eiki LC-X70 stands out as a powerful, versatile projector, ideal for various professional environments. With its combination of high brightness, excellent color accuracy, and multiple connectivity options, it enhances presentations, lectures, and meetings, ensuring that content is delivered with maximum impact.
Top Page Image Contents