Eiki LC-X70 Appendix Lamp Replace Counter, Message Lamp replace counter reset? is displayed. Move

Page 45

APPENDIX

LAMP REPLACE COUNTER

Be sure to reset the Lamp Replace Counter after the Lamp Assembly is replaced. When the Lamp Replace Counter is reset, the LAMP REPLACE Indicator stops lighting.

1

Turn projector on, press MENU button and ON-SCREEN

 

MENU will appear. Press POINT LEFT/RIGHT button(s) to

 

move a red frame pointer to SETTING Menu icon (refer to

 

page 40).

2

Press POINT UP/DOWN button to move a red frame pointer

 

to “Lamp counter reset” and then press SELECT button. The

 

message "Lamp replace counter reset?" is displayed. Move

 

the pointer to [Yes] and then press SELECT button.

3

Another confirmation dialog box appears and select [Yes] to

reset Lamp Replace Counter.

Move the pointer to Lamp counter reset and then press SELECT button. The message “Lamp replace counter reset?” is displayed.

NOTE : Do not reset the Lamp Replace Counter until after the Projection Lamp is replaced.

LAMP HANDLING PRECAUTIONS

This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may result in accidents, injury, or create a fire hazard.

Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than other similar lamps.

If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.

( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual. ) Continuous use of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.

A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.

IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.

If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.

45

Image 45
Contents Multimedia Projector Model LC-X70To the Owner Voor de klanten in Nederland Safety InstructionsEsperanza Rancho Santa Margarita CA CompliancesTable of Contents Compact Design Digital Zoom for Computer Features and DesignPreparation Name of Each Part of ProjectorHOT AIR Exhausted SETTING-UP Projector Connecting AC Power CordFor U.S.A. and Canada For Continental Europe Room Light Preparation Positioning ProjectorInstalling Projector in Proper Position Preparation Adjustable FeetPreparation Moving Projector Terminals of Projector Connecting ProjectorConnect computer output Digital DVI-D type to this terminal Refer to P13Terminals Connecting to ComputerA Projector Front of the projector Audio Input External Audio Equipment Audio SpeakerA Projector Connecting to Video EquipmentInside the Battery Compartment BOX Operation of Remote ControlBefore Operation Laser Pointer FunctionTimer Button Point Volume + ButtonsZoom Button Select ButtonPoint Volume + / Buttons TOP Controls and IndicatorsHOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Used to adjust picture image Press Menu Button while connecting to PC input sourceBefore Operation Menu BAR Used to selectTurning on / OFF Projector Basic OperationTurning on Projector Turning OFF ProjectorKeystone Adjustment Adjusting ScreenFocus adjustment may not function properly if the image is Corrected by Keystone adjustmentSound Adjustment Selecting Input Source Computer InputSelecting Computer System Rgbav HdcpAutomatic MULTI-SCAN System AutoPC System Menu Auto PC Adjustment PC AdjustmentPC Adjust Menu Auto PC AdjComputer Input Manual PC Adjustment Display area Display area HFull screen Image Level Select Direct Picture Image SelectImage Level Select Menu Image 1~4Screen Menu Picture Screen AdjustmentVideo Input When video input signal is connected to Y-Pb/CbVideo Select VideoSelecting Video System Component Video Signal FormatPAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N AV System Menu Video or S-VIDEOCinema Picture level adjusted for picture with fine toneProvides image at a wide screen ratio of 16 Provides image at a normal video aspect ratio of 4Picture Image Adjustments Image Adjust MenuPicture Image Picture Image List ModeWhite balance Red Color tempWhite balance Green White balance BlueSetting Setting MenuSetting Menu Blue back AnamorphicDisplay Menu positionPower management To change the code of the Remote Control UnitRemote control To change the code of ProjectorWireless Mouse mode Projector modeUSB Installation Operating Wireless MouseOperating Wireless Mouse AppendixSection AIR Filter Care and Cleaning on next MaintenanceIndicatorIndicator Projector so that Ventilation Slots are not obstructedCleaning Projection Lens Appendix AIR Filter Care and CleaningRecommendation Pull up and removeLamp Replace Lamp ReplacementReset Lamp Replace Counter Message Lamp replace counter reset? is displayed. MoveAppendix Lamp Replace Counter Pointer to Yes and then press Select buttonTroubleshooting Wireless Mouse Remote Control UnitDoes not work Function does notAppendix Indicators and Projector Condition Resolution Appendix Compatible Computer SpecificationsPC source Menu TreeSystem Setting Sound Technical Specifications Control Port Connector Appendix Configurations of TerminalsUSB Connector Series B Computer INPUT-1 and Monitor OUT Terminals AnalogAppendix Optional Parts Lens ReplacementAppendix Key to better communications Canada
Related manuals
Manual 56 pages 34.59 Kb

LC-X70 specifications

The Eiki LC-X70 is a high-performance multimedia projector designed for a variety of applications, including education, business, and large venues. Known for its versatility and advanced features, the LC-X70 offers exceptional image quality and user-friendly operation.

One of the standout features of the LC-X70 is its impressive brightness level, reaching up to 6,500 ANSI lumens. This high brightness capability makes it ideal for use in well-lit environments, ensuring that presentations maintain clarity and visibility. Coupled with a high contrast ratio, the projector delivers vivid colors and deep blacks, enhancing the overall viewing experience.

The LC-X70 utilizes advanced 3LCD technology, which ensures accurate color reproduction and reduces the risk of color fading over time. This technology enables the projector to produce images that are both bright and vibrant, making it suitable for projecting detailed graphics and videos. Furthermore, it supports resolutions up to WUXGA (1920 x 1200), allowing it to display high-definition content with stunning clarity.

Connectivity is another strong point for the Eiki LC-X70. It boasts a variety of input options, including HDMI, VGA, and USB ports, allowing users to connect multiple devices seamlessly. This flexibility makes it easy to integrate the projector into existing setups, whether in classrooms, conference rooms, or auditoriums. The inclusion of wireless connectivity options further enhances its usability, enabling users to project from laptops, tablets, and smartphones without the need for cables.

In addition to its impressive performance features, the LC-X70 is designed with user convenience in mind. It includes a user-friendly remote control, simplifying navigation through settings and options. The projector also features a built-in speaker, providing adequate audio output for presentations. For extended use cases, the projector is equipped with a long-lasting lamp, resulting in reduced maintenance costs.

In terms of portability, the Eiki LC-X70 is relatively compact and lightweight, making it easy to transport between locations. Its robust construction ensures durability, making it a reliable choice for users who require a projector that can withstand regular use.

Overall, the Eiki LC-X70 stands out as a powerful, versatile projector, ideal for various professional environments. With its combination of high brightness, excellent color accuracy, and multiple connectivity options, it enhances presentations, lectures, and meetings, ensuring that content is delivered with maximum impact.