Classe Audio CA-2100 owner manual Specifications

Page 22

22

Specifications

Classé Audio reserves the right to make improvements without notice.

Power output

100W/ch continuous rms @ 8Ω

 

(both channels driven)

200W/ch continuous rms @ 4Ω

Frequency response

 

10Hz – 22kHz (+0/-0.1dB)

 

Phase

 

10Hz – 155kHz (+0/-3.0dB)

 

better than -10° @ 22kHz

Signal-to-noise ratio

 

better than -105dB

 

Channel separation

(ref. full ouput, 10Hz – 80kHz)

 

better than 110dB @ 20kHz

Noise floor (FFT)

 

all peaks less than -95dBV

 

Distortion (THD + noise)

 

(10Hz – 80kHz)

 

0.003% @ 8Ω

 

(unweighted, 1.0Vrms/1kHz input, 10Hz – 500kHz)

Voltage gain

 

 

29.1dB

Sensitivity

1.0Vrms for rated output @ 8Ω

Input Impedance

 

 

100kΩ

Rated power consumption (as per IEC60065 para. 2.3.10)

260W

Idle power consumption

 

 

104W

Mains voltage

 

specified on rear panel

 

 

(cannot be changed by dealer or user).

Dimensions (not incl. controls or connectors)

Width: 17.5” (445mm)

 

 

 

Height: 4.75” (121mm)

 

Shipping weight

 

Depth: 16.5” (419mm)

 

 

55 lbs (25kg)

Net weight

 

 

47 lbs (21kg)

For more information, see your Classé dealer, or contact:

Classé Audio

5070 François Cusson

Lachine, Quebec

Canada H8T 1B3

Telephone

+1 (514) 636-6384

FAX

+1 (514) 636-1428

http://www.classeaudio.com email: cservice@classeaudio.com

Classé and the Classé logo are trademarks of Classé Audio Inc. of Lachine, Canada. All rights reserved. i-Command™ is a trademark of Equity International, Inc. All rights reserved.

AMX® is a registered trademark of AMX Corporation of Richardson, TX. All rights reserved. Crestron™ is a trademark of Crestron Electronics, Inc. of Rockleigh, NJ. All rights reserved.

Image 22
Contents CA-2100 Power Amplifier Page Important Safety Instructions Serial #Contents Word about installation Welcome to the Classé familyUnpacking and Placement Unpacking your amplifier Placement VentilationCustom installations Serial number Operating voltageWarm up/break-in period Please read this manual… Special Design Features Extraordinary longevity Robust protection Front Panel Standby button & LED indicatorOff + Channel LED on Mode button Channel status LED indicatorsSelect button Rear Panel Balanced XLR InputSingle-Ended RCA Input Speaker OutputsClassé can Bus Control Ports IR Input and OutputAC Mains Input RS-232 Control Port This DB-9 connector has two purposesDC Trigger Input and Output AC Mains FuseInitial Setup Configure your amplifierMake your preamp connections Make your speaker connectionsCare and Maintenance Double-check all your connectionsNo sound, and one or more Channel LEDs is blinking red TroubleshootingNo sound, and no Channel LED is lit Amplifier keeps shutting offAC mains fuse is blown Specifications Dimensions V1.9 020405

CA-2100 specifications

The Classe Audio CA-2100 is a high-performance stereo power amplifier that exemplifies the brand's commitment to delivering exceptional sound quality, robust construction, and advanced technology. Designed for audiophiles and music enthusiasts, the CA-2100 offers outstanding amplification capabilities, ensuring that even the most nuanced audio details are captured and reproduced with clarity.

One of the standout features of the CA-2100 is its impressive power output. With a rating of 200 watts per channel at 8 ohms, and 400 watts at 4 ohms, this amplifier provides ample headroom to drive a wide range of speakers with ease. Whether you're listening to delicate acoustic performances or the most demanding orchestral pieces, the CA-2100 can handle it all without distortion. Its dual-mono architecture ensures that each channel is powered independently, minimizing crosstalk and delivering a pure, immersive stereo experience.

The CA-2100 incorporates advanced Class AB amplification technology, which strikes a perfect balance between the efficiency of Class D and the sound quality associated with Class A amplifiers. This design allows the amplifier to deliver warm, rich sound while maintaining the dynamic responsiveness crucial for live performances.

A key characteristic of the CA-2100 is its premium build quality. The amplifier features an aluminum chassis that not only enhances durability but also contributes to effective heat dissipation. This thoughtful design helps maintain optimal operating temperatures, ensuring longevity and reliable performance over time. The amplifier is also equipped with a high-quality power supply that delivers stable and consistent power to the output stage.

Additional features of the CA-2100 include a variety of input options, including balanced XLR and single-ended RCA connectors. This versatility allows users to integrate the amplifier into a wide range of audio systems with ease. Furthermore, the CA-2100 is designed with user-friendly functionality, featuring a straightforward layout with intuitive controls.

In summary, the Classe Audio CA-2100 stands out in the realm of audio amplification with its powerful performance, elegant design, and advanced technology. It serves as an excellent choice for those seeking to elevate their listening experience, delivering music in its most authentic form. Whether in a dedicated listening room or a high-end home theater, the CA-2100 is sure to impress even the most discerning audiophiles.