Eiki LC-SXG400L owner manual Projector is shut down and all five indicators are blinking

Page 61

Maintenance and Filter Cleaning

Warning Indicators

The WARNING indicators show the state of the function which protects the projector. Check the state of the WARNING indicators and the POWER indicator to take proper maintenance.

The projector is shut down and the WARNING TEMP. indicator is blinking red.

When the temperature inside the projector reaches a certain level, the projector will be automatically shut down to protect the inside of the projector. The POWER indicator is blinking while the projector is being cooled down. When the projector has cooled down enough (to its normal operating temperature), it can be turned on again by pressing the ON/STAND-BY button.

Note:

Top Control

WARNING TEMP.. blinking red

The WARNINGTEMP. indicator continues to blink even after the temperature inside the projector returns to normal. When the projector is turned on again, the WARNINGTEMP. indicator stops blinking.

Then check the matters below:

Did you provide appropriate space for the projector to be ventilated? Check the installing condition to see if the air vents of the projector are not blocked.

Has the projector been installed near an Air-Conditioning/ Heating Duct or Vent? Move the installation of the projector away from the duct or vent.

Is the filter clean? Clean the filter periodically or replace it with a new one.

The projector is shut down and all five indicators are blinking.

When the projector detects an abnormal condition, it will be automatically shut down to protect the inside of the projector and all five indicators on the top panel blink. In this case, unplug the AC power cord and plug it, and then turn on the projector once again to verify operation. If the projector cannot be turned on and these indicators are still blinking, unplug the AC power cord and contact the service station.

CAUTION

DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER AN ABNORMAL CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC SHOCK.

Top Control

All five indicators are blinking

61

Image 61
Contents Model LC-SXG400 LC-SXG400L Features and Design Table of Contents Risk of Electric Shock Do not Open To the OwnerSafety Instructions Top Control Air CirculationPositioning Precautions Installing the Projector in Proper DirectionsTransporting the Projector Moving the ProjectorAC Power Cord for the United Kingdom AC Power Cord for the United States and CanadaCompliance Front Back Bottom Part Names and FunctionsKensington Security Slot Rear Terminal 4Infrared Remote Receiver Back Reset buttonTop Control Remote Control 9RESET/ON/ALL-OFF switch 4P-TIMER button@0FOCUS button Adjust the focus p.30 @1NO Show button 3MENU buttonAdjustable Feet Remote Control Battery InstallationRemote Control Code Positioning the Projector for LC-SXG400 InstallationMoving the Lens Removing the lens Lens InstallationAttaching the lens to the projector Cables used for connection Connecting to a Computer Digital and Analog RGBConnecting to Video Equipment Video, S-Video Connecting to Video Equipment Component and RGB Scart Projector side AC outlet side Connecting the AC Power CordBasic Operation What is PIN code?Turning On the Projector Enter a PIN codeTurning Off the Projector Remote Control How to Operate the On-Screen MenuOn-Screen Menu Menu Bar Lens Operation Operating with Projector ControlInformation Direct Operation Sound AdjustmentMenu Operation Operating with Remote Control No Show button Timer buttonKeystone button Pointer Function Laser Pointer FunctionSpotlight Presentation Pointer button Wireless Mouse OperationInput Selection Remote Control OperationInput Top Control OperationInput Menu Input Source SelectionRGB PC analog RGB Scart RGB PC digital Video ComponentVideo or S-Video Video System SelectionComponent AV System Menu Video or S-VideoComputer System Selection Computer AdjustmentSelecting Computer System Manually PC System MenuPC Adjust Menu Auto PC AdjustmentTo store adjustment parameters Auto PC AdjManual PC Adjustment To store the adjusted data To clear the adjusted dataImage Level Selection Image Level SelectionImage Menu Image Adjustment Image AdjustmentImage Adjust Menu Gamma SharpnessNoise reduction ProgressiveTo reset the adjusted data, select Reset and press Screen Adjustment Screen AdjustmentScreen Menu KeystoneScreen Size Adjustment Computer Signals Digital zoom + For zooming in and out the imagesDigital zoom Screen Size Adjustment Video, Component Signals Setting SettingSetting Menu Language PointerLogo Capture Logo Logo and Logo PIN code lock settingsLogo select CaptureEnter a Logo PIN code Change the Logo PIN code lock settingChange the Logo PIN code Remote control Display On start Power managementFan control Fan control settingKey lock Change the PIN code lock setting Change the PIN code lock settingPIN code lock Enter a PIN codeChange the PIN code Change the PIN codeTest pattern Lamp counterFactory default Factory defaultFilter counter Filter counterReinstall the filter into the projector properly Reset the lamp counter Lamp ReplacementPOA-LMP116 Service Parts No 335 Lamp counter Resetting the Lamp CounterThen check the matters below Projector is shut down and all five indicators are blinkingCleaning the Projector Cabinet Cleaning the Projection LensProblem TroubleshootingNo power AppendixDuring the operation Setting does not remain after Auto PC adjustment functionTurning off power Power management function doesAppendix Input Menu TreeSystem InformationSetting PC AdjustProjector Condition Indicators and Projector ConditionResetting the counter Lamp Replace indicatorON-SCREEN Resolution Compatible Computer SpecificationsSpecifications are subject to change without notice Technical Specifications Optional Parts PJ Link Notice USB Connector Series B Configurations of TerminalsTerminal Analog RGB Mini D-sub 15 pin Input OutputLogo PIN Code Lock No PIN Code Number MemoDimensions China Deutschland & ÖsterreichCanada Eastern Europe