Eiki LC-SXG400L owner manual Lamp Replace indicator, Resetting the counter

Page 69

Appendix

WARNING FILTER indicator

Indicators

POWER

LAMP

WARNING

FILTER

green

red

orange

 

 

Projector Condition

Filter warning red icon

The filter is clogged. Stop using the projector immediately and clean or replace the filter (see below).

– –

Filter warning yellow icon

The Filter counter reached a set time. Clean or replace the filter as soon as possible.

If filter clogging is detected during operations, the Filter warning icon (red) appears on the screen and the WARNING FILTER indicator blinks orange, urging you to clean or replace the filter. Stop using the projector immediately and clean or replace the filter. The WARNING FILTER indicator and Filter warning icon will not be turned off until the filter is cleaned or replaced by a new one.

Filter warning icon (red) appears on the screen when the projector detects filter clogging.

Note:

The Filter warning icon (red) will not appear during “Freeze” (p.30), or “No show” (p.31).

LAMP REPLACE indicator

 

Indicators

 

POWER

 

LAMP

LAMP

Projector Condition

 

REPLACE

 

green

 

red

 

 

yellow

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The lamp cannot light up. (The projector is preparing for stand-by or

 

 

 

 

the projection lamp is being cooled down. The projector cannot be

 

 

 

 

turned on until cooling is completed.)

 

 

 

 

 

 

 

 

 

The lamp cannot light up. (The lamp has been cooled down enough

 

 

 

 

and the projector is in stand-by mode and ready to be turned on with

 

 

 

 

the ON/STAND-BY button.)

 

 

 

 

 

 

 

The lamp has been used overtime. Replace the lamp immediately

 

 

and then reset the lamp counter. The indicator will be turned off after

 

 

 

 

resetting the counter.

 

 

 

 

 

*When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow, replace the projection lamp with a new one promptly. Reset the lamp counter after replacing the lamp. See pages 59–60.

69

Image 69
Contents Model LC-SXG400 LC-SXG400L Features and Design Table of Contents Risk of Electric Shock Do not Open To the OwnerSafety Instructions Top Control Air CirculationPositioning Precautions Installing the Projector in Proper DirectionsTransporting the Projector Moving the ProjectorAC Power Cord for the United States and Canada AC Power Cord for the United KingdomCompliance Part Names and Functions Front Back BottomKensington Security Slot Rear Terminal 4Infrared Remote Receiver Back Reset buttonTop Control Remote Control 9RESET/ON/ALL-OFF switch 4P-TIMER button@0FOCUS button Adjust the focus p.30 @1NO Show button 3MENU buttonAdjustable Feet Remote Control Battery InstallationRemote Control Code Installation Positioning the Projector for LC-SXG400Moving the Lens Lens Installation Removing the lensAttaching the lens to the projector Cables used for connection Connecting to a Computer Digital and Analog RGBConnecting to Video Equipment Video, S-Video Connecting to Video Equipment Component and RGB Scart Projector side AC outlet side Connecting the AC Power CordBasic Operation What is PIN code?Turning On the Projector Enter a PIN codeTurning Off the Projector How to Operate the On-Screen Menu Remote ControlOn-Screen Menu Menu Bar Operating with Projector Control Lens OperationInformation Sound Adjustment Direct OperationMenu Operation Operating with Remote Control Timer button No Show buttonKeystone button Laser Pointer Function Pointer FunctionSpotlight Presentation Pointer button Wireless Mouse OperationInput Selection Remote Control OperationInput Top Control OperationInput Menu Input Source SelectionRGB PC analog RGB Scart RGB PC digital Video ComponentVideo or S-Video Video System SelectionComponent AV System Menu Video or S-VideoComputer System Selection Computer AdjustmentSelecting Computer System Manually PC System MenuPC Adjust Menu Auto PC AdjustmentTo store adjustment parameters Auto PC AdjManual PC Adjustment To store the adjusted data To clear the adjusted dataImage Level Selection Image Level SelectionImage Menu Image Adjustment Image AdjustmentImage Adjust Menu Gamma SharpnessNoise reduction ProgressiveTo reset the adjusted data, select Reset and press Screen Adjustment Screen AdjustmentScreen Menu KeystoneScreen Size Adjustment Computer Signals For zooming in and out the images Digital zoom +Digital zoom Screen Size Adjustment Video, Component Signals Setting SettingSetting Menu Language PointerLogo Capture Logo Logo and Logo PIN code lock settingsLogo select CaptureChange the Logo PIN code lock setting Enter a Logo PIN codeChange the Logo PIN code Remote control Display On start Power managementFan control setting Fan controlKey lock Change the PIN code lock setting Change the PIN code lock settingPIN code lock Enter a PIN codeChange the PIN code Change the PIN codeTest pattern Lamp counterFactory default Factory defaultFilter counter Filter counterReinstall the filter into the projector properly Lamp Replacement Reset the lamp counterPOA-LMP116 Service Parts No 335 Lamp counter Resetting the Lamp CounterThen check the matters below Projector is shut down and all five indicators are blinkingCleaning the Projector Cabinet Cleaning the Projection LensProblem TroubleshootingNo power AppendixDuring the operation Setting does not remain after Auto PC adjustment functionTurning off power Power management function doesAppendix Input Menu TreeSystem InformationSetting PC AdjustProjector Condition Indicators and Projector ConditionResetting the counter Lamp Replace indicatorON-SCREEN Resolution Compatible Computer SpecificationsSpecifications are subject to change without notice Technical Specifications Optional Parts PJ Link Notice USB Connector Series B Configurations of TerminalsTerminal Analog RGB Mini D-sub 15 pin Input OutputLogo PIN Code Lock No PIN Code Number MemoDimensions China Deutschland & ÖsterreichCanada Eastern Europe