Intel PCA-6175 manual Introduction

Page 12

1.1Introduction

The PCA-6175 industrial grade CPU card uses Intel's highly acclaimed Pentium® II processor and Intel 440LX PCI chipset. The card works with standard ISA or PCI/ISA-bus passive backplanes.

The CPU provides 512 KB on-chip L2 cache, eliminating the need for external SRAM chips. It has two PCI EIDE interfaces (for up to four devices), and an FDD interface (for up to two devices). Other features include two RS-232 serial ports (16C550 UARTs with 16-byte FIFO or compatible), one enhanced parallel port (supports EPP/ECP), and support for two USB (Universal Serial Bus) ports. The PCI BUS Master IDE controller supports Ultra DMA/33 operation. This provides data transfer rates of over 33 MB/sec, and allows drive capacities up to 8.4 GB. System BIOS supports boot-up from an IDE CD-ROM.

A backup of CMOS data is stored in the Flash memory, which protects data even after a battery failure. Also included is a 63-level watchdog timer, which resets the CPU or generates an interrupt if a program cannot be executed normally. This enables reliable operation in unattended environments.

2PCA-6175 User's Manual

Image 12
Contents PCA-6175 Copyright Notice Acknowledgements Advantech Customer Services Message to the CustomerTechnical Support Product Warranty Initial inspection Contents Connecting Peripherals Award Bios Setup Appendix B Pin Assignments Keyboard and Mouse Connnector CN12Page Hardware Configuration Introduction Features Specifications SystemMemory Input/OutputIndustrial features Mechanical and environmental specificationsBoard Layout Main Features Jumpers and Connectors Label FunctionNumber Function Board Layout Jumper Locations Board layout jumper locationsBoard Layout Connector Locations Board layout connecter locationsSafety Precautions Jumper Settings How to set jumpersCPU core frequency J5 Watchdog timer output J8 Cmos clear J6CPU bus clock select J11 DiskOnChip 2000 Flash disk address select J12 System Memory Sample calculation Dimm memory capacitySupplementary information about DIMMs Memory Installation Procedures Dimm installationCache Memory Mounting the CPU and Cooling Modules Mounting CPU and cooling modules StepStep On-board Support Bracket On-board support bracketConnecting Peripherals Primary CN6 and Secondary CN7 IDE Connectors Floppy Drive Connector CN13Parallel Port Connector CN8 Keyboard & PS/2 Mouse Connector CN12Serial Ports CN9 COM1 CN10 COM2 Front Panel Connectors CN2, CN3, CN4, J1 and J2 ATX Power Control Connectors J7 and J1 ATX feature connector J7 and soft power switch connector J1USB Connector CN11 IR Connector CN1External Keyboard Connector J10 Controlling the soft power switchExternal Suspend Switch Lead SMI J3 Award Bios Setup Entering Setup Standard Cmos SetupBios Features Setup Virus WarningQuick Power On Self Test Boot SequenceBoot Up Floppy Seek Boot Up System Speed IDE HDD Block ModeTypematic Rate Setting Gate A20 OptionTypematic Delay msec Video Bios ShadowSecurity Option OS Select for Dram 64 MBChipset Features Setup Chipset features setup screenPower Management Setup Power ManagementHDD Power Management PCI Configuration Setup Load Bios DefaultsLoad Setup Defaults IRQ ActivityIntegrated Peripherals Integrated peripheralsPassword Setting IDE HDD Auto DetectionSave & Exit Setup Exit Without SavingProgramming the Watchdog Timer Programming the Watchdog Timer Data Time IntervalGosub 2000 REM Your application task #2 Page Pin Assignments COM1/COM2 RS-232 Serial Port CN9,CN10 Keyboard and Mouse Connnector CN12ATX Feature Connector J7 IDE Hard Drive Connector CN6, CN7CPU Fan Power Connector CN5 Table B-8 Floppy drive connector CN13 \STROBE HDD LED Connector CN4 Power LED and Keylock Connector CN2External Speaker CN3 System I/O Ports Addr. range Hex DeviceDMA Channel Assignments Interrupt AssignmentsVGA Bios 17 1st MB Memory MapPage DOC 2000 Installation Guide DiskOnChip 2000 Quick Installation Guide DiskOnChip 2000 installation instructionsAdditional information and assistance