Intel PCA-6175 manual Copyright Notice Acknowledgements

Page 2

Copyright Notice

This document is copyrighted, 1998, by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd., reserves the right to make improvements to the products described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements upon the rights of third parties which may result from its use.

Acknowledgements

AWARD is a trademark of AWARD Software, Inc. AMD is a trademark of Advanced Micro Devices, Inc.

IBM and PC are trademarks of International Business Machines Corporation.

Intel is a trademark of Intel Corporation. MS-DOS is a trademark of Microsoft Corporation.

SMC is a trademark of Standard Microsystems Corporation. NCR is a trademark of NCR Corporation.

All other product names or trademarks are the properties of their respective owners.

Part No. 2006617500	1st Edition
Printed in Taiwan	May 1998

ii

Image 2

Contents PCA-6175 Copyright Notice Acknowledgements Technical Support Advantech Customer ServicesMessage to the Customer Product Warranty Initial inspection Contents Connecting Peripherals Award Bios Setup Appendix B Pin Assignments Keyboard and Mouse Connnector CN12Page Hardware Configuration Introduction Features Memory SpecificationsSystem Input/OutputIndustrial features Mechanical and environmental specificationsBoard Layout Main Features Jumpers and Connectors Label FunctionNumber Function Board Layout Jumper Locations Board layout jumper locationsBoard Layout Connector Locations Board layout connecter locationsSafety Precautions CPU core frequency J5 Jumper SettingsHow to set jumpers Watchdog timer output J8 Cmos clear J6CPU bus clock select J11 DiskOnChip 2000 Flash disk address select J12 System Memory Sample calculation Dimm memory capacitySupplementary information about DIMMs Memory Installation Procedures Dimm installationCache Memory Mounting the CPU and Cooling Modules Mounting CPU and cooling modules StepStep On-board Support Bracket On-board support bracketConnecting Peripherals Primary CN6 and Secondary CN7 IDE Connectors Floppy Drive Connector CN13Parallel Port Connector CN8 Keyboard & PS/2 Mouse Connector CN12Serial Ports CN9 COM1 CN10 COM2 Front Panel Connectors CN2, CN3, CN4, J1 and J2 ATX Power Control Connectors J7 and J1 ATX feature connector J7 and soft power switch connector J1External Keyboard Connector J10 USB Connector CN11IR Connector CN1 Controlling the soft power switchExternal Suspend Switch Lead SMI J3 Award Bios Setup Entering Setup Standard Cmos SetupBios Features Setup Virus WarningBoot Up Floppy Seek Quick Power On Self TestBoot Sequence Typematic Rate Setting Boot Up System SpeedIDE HDD Block Mode Gate A20 OptionSecurity Option Typematic Delay msecVideo Bios Shadow OS Select for Dram 64 MBChipset Features Setup Chipset features setup screenHDD Power Management Power Management SetupPower Management Load Setup Defaults PCI Configuration SetupLoad Bios Defaults IRQ ActivityIntegrated Peripherals Integrated peripheralsPassword Setting IDE HDD Auto DetectionSave & Exit Setup Exit Without SavingProgramming the Watchdog Timer Programming the Watchdog Timer Data Time IntervalGosub 2000 REM Your application task #2 Page Pin Assignments COM1/COM2 RS-232 Serial Port CN9,CN10 Keyboard and Mouse Connnector CN12ATX Feature Connector J7 IDE Hard Drive Connector CN6, CN7CPU Fan Power Connector CN5 Table B-8 Floppy drive connector CN13 \STROBE HDD LED Connector CN4 Power LED and Keylock Connector CN2External Speaker CN3 System I/O Ports Addr. range Hex DeviceDMA Channel Assignments Interrupt AssignmentsVGA Bios 17 1st MB Memory MapPage DOC 2000 Installation Guide DiskOnChip 2000 Quick Installation Guide DiskOnChip 2000 installation instructionsAdditional information and assistance