Intel AX965Q Primary Eide Connector Prieide, Drive jumper setting Mode of devices Cable connector

Page 48

ATX Main board

1.8.2.14 Primary EIDE Connector (PRI_EIDE)

The onboard IDE connector is for the Ultra DMA 133/100/66 signal cable. There are three connectors on each Ultra DMA 133/100/66 signal cable: blue, black, and gray. Connect the blue connector to the motherboard’s IDE connector, then select one of the following modes to configure your device.

		Drive jumper setting		Mode of device(s)		Cable connector
Single device		Cable-select or Master		-		Black
		Cable-select		Master		Black
Two devices		Cable-select		Slave		Gray
				Slave		Gray

		Master		Master		Black or Gray
		Master		Master

		Slave		Slave
		Slave		Slave

zPin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable.

zUse the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE devices.

If any device jumper is set as “Cable-Select,” make sure all other device jumpers have the same setting

zOrient the red markings (usually zigzag) on the IDE cable to Pin 1.

48

Image 48

Contents AX965Q User’s Manual VerContents User’s Manual Safety Information Technical Support Packing List Revision History Specifications Summary Hmdi Block Diagram Product1 introduction Production Introduction Before you ProceedPlacement Direction Motherboard OverviewScrew Holes Motherboard Layout Layout Content List Label FunctionInternal Connector Central Processing Unit CPU Installing the CPU User’s Manual Installing the CPU Heatsink and Fan User’s Manual Uninstalling the CPU Heatsink and Fan User’s Manual System Memory Dimm Sockets LocationMemory Configurations 32-bit 64-bitQualified Vendors Lists QVL － DDR2-800MHz Capability Size Vender Chip. No Dimm supportQualified Vendors Lists QVL － DDR2-667MHz Capability AM4B5708GQJS7E AU512E667C5KBGC Qualified Vendors Lists QVL － DDR2-553MHz Capability Kingston 5YDIID9GCTInstalling a Dimm Removing a Dimm Installing an Expansion Card Configuring an Expansion CardExpansion Slots Standard Interrupt Assignments IRQPCI Slots PCI Express X16 SlotPCI Express X4 Slot Jumpers Clear RTC RAM ClrtcKeyboard Power Kbpwr Connectors Rear Panel ConnectorsHeadset Port Channel PS/2 KB connector This port is for a PS/2 keyboard Internal Connectors Front Panel Audio Connector Aafp ATX Power Connector ATX12V, Eatxpwr Important notes on the Motherboard Power RequirementsOptical Drive Audio Connector CD CPU & Chassis Fan Connector CPUFAN, CHAFAN1, CHAFAN2 ATX Main board User’s Manual System Panel Connector Fpanel System Power LED 2-pin PwrledATX Power Button/Soft-off Button 2-pin Pwrsw Reset Button 2-pin ResetSignal Signal Description Primary Eide Connector Prieide Drive jumper setting Mode of devices Cable connectorDigital Audio Connector Spdifout Serial ATA RAID Connector SATARAID1 USB 2.0 Connector USB56, 78 Trusted Platform Module TPM Connector TPMSLOT1 Bios setup2 Bios Setup Bios Setup ProgramList Box Sub-menuBios Menu Screen Standard Cmos Features IDE Device SetupDate Day, xx/xx/xxxx TimeDriver A/B VideoHalt On MemoryAdvanced Bios Features CPU Features Quick Power On Self Test CPU L1 & L2 & L3 CacheFirst / Second / Third Boot Device Boot Other DeviceBoot Up Floppy Seek Swap Floppy DriveBoot Up NumLock Status Typematic Rate SettingGate A20 Option Typematic Rate Chars/SecApic Mode MPS Version Control for OSOS Select for Dram 64MB Small Logo EPA ShowAdvanced Chipset Features System Bios CacheableMemory Hole at 15M-16M Dvmt Mode PCI Express Root Port Function 3.4 PEG/Onchip VGA ControlOn-Chip Frame Buffer Size DVMT/FIXED Memory SizeIntegrated Peripherals OnChip IDE Device Super I/O Device Watch Dog Timer Select USB Device Setting Power Management Setup Run Vgabios if S3 ResumeAcpi Function Acpi Suspend TypePower Management Suspend ModeVideo Off Method Video Off In SuspendHDD Power Down Power On by RingResume by Alarm Soft-off by PWR-BTTN6 PnP/PCI Configurations Init Display First Rest Configuration DataResource Controlled By Maximum Payload Size Frequency/Voltage Control CPU Clock RatioAuto Detect PCI Clk Spread SpectrumLoad Fail-Safe Defaults Load Optimized Defaults Set Supervisor/User Password Please Confirm Your PasswordSave and Exit Setup Exit Without Saving