Intel GA-8I945GZME-RH Frequency/Voltage Control, CPU Clock Ratio Note, System Memory Multiplier

Page 44

English

2-7

Frequency/Voltage Control

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

 

 

 

 

Frequency/Voltage Control

 

 

 

CPU Clock Ratio (Note)

[18X]

 

 

Item Help

 

System Memory Multiplier

[Auto]

 

Menu Level`

 

Memory Frequency (Mhz)

533

 

Set CPU Ratio if CPU

 

 

 

 

 

 

 

 

 

 

Ratio is unclocked

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

F6: Fail-Safe Defaults

 

F7: Optimized Defaults

 

 

 

 

 

 

 

Incorrect using these features may cause your system broken. For power end-user use only.

CPU Clock Ratio (Note)

This setup option will automatically assign by CPU detection.

The option will display "Locked" and read only if the CPU ratio is not changeable.

System Memory Multiplier

Wrong frequency may make system can't boot, clear CMOS to overcome wrong frequency issue. for FSB(Front Side Bus) frequency=533MHz,

3

Memory Frequency = Host clock X 3.

4

Memory Frequency = Host clock X 4.

Auto

Set Memory frequency by DRAM SPD data. (Default value)

for FSB(Front Side Bus) frequency=800MHz,

2.0

Memory Frequency = Host clock X 2.0.

2.66

Memory Frequency = Host clock X 2.66.

Auto

Set Memory frequency by DRAM SPD data. (Default value)

Memory Frequency (Mhz)

The values depend on "System Memory Multiplier" item.

(Note) This item will show up when you install a processor which supports this function.

GA-8I945GZME-RH Motherboard

- 44 -

Image 44
Contents GA-8I945GZME-RH GA-8I945GZME-RH Copyright Product Manual ClassificationTable of Contents Install Drivers Item Checklist GA-8I945GZME-RH Motherboard Layout Block Diagram Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPU4Mbit flash ROM Installation of the CPU and CPU Cooler Installation of the CPUInstallation of the Heatsink Installation of Memory Installation of Expansion Cards Dual Channel Memory ConfigurationGraphics Card Support List PX6600GT TDHI/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector IDE IDE ConnectorFDD FDD Connector SATAII0 / SATAII1 / SATAII2 / SATAII3 Sata 3Gb/s ConnectorsFaudio Front Audio Connector PwrledFpanel Front Panel Jumper Cdin CD In Connector Spdifio Spdif In/OutHdasur Surround Center Connector FUSB1/FUSB2 Front USB ConnectorsComb Comb Connector CI Chassis Intrusion, Case OpenClrcmos Clear Cmos English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E7 F12 For Boot Menu„ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationStandard Cmos Features DateTime IDE Channel 0 Master/SlaveFloppy 3 Mode Support for Japan Area Drive aHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckCPU Hyper-Threading Limit Cpuid Max. toNo-Execute Memory ProtectNote CPU Enhanced Halt C1E NoteIntegrated Peripherals SPPOnboard LAN Boot ROM USB 2.0 ControllerUSB Keyboard Support USB Mouse SupportOnboard Parallel port Parallel Port ModeECP Mode Use DMA Power Management Setup Acpi Suspend TypeAC Back Function Power On By KeyboardKB Power on Password PnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status CPU Smart FAN Mode CPU Smart FAN ControlFrequency/Voltage Control CPU Clock Ratio NoteSystem Memory Multiplier Memory Frequency MhzLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Install Drivers Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to 4 to flash the backup BIOS, too Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Audio Jacks Introduction Installing the 5.1/7.1 Surround Cable Optional4 2- / 4- / 6- / 8- Channel Audio Introduction Setting Up Stereo Speakers HD AudioSetting Up 4-Channel Audio Setting Up 6-Channel Audio Setup Setting Up 8-Channel Audio Sound Effect Configuration Troubleshooting English English English English English English English Contact Us Taiwan HeadquartersGigabyte Global Service System