Intel 8I845PE-RZ Hardware Installation Process, Install the Central Processing Unit CPU, Step

Page 8

English

Hardware Installation Process

To set up your computer, you must complete the following steps:

Step 1- Install the Central Processing Unit (CPU)

Step 2- Install mem ory modules

Step 3- Install expansion cards

Step 4- Connect ribbon cables, cabinet wires, and power supply

Step 4 Step 1 Step 2

Step 4

Step 4

Step 3

Step 1: Install the Central Processing Unit (CPU)

Before installing the processor, adhere to the following warning:

1 .

Please m ake sure the CPU type is supported by the m otherboard.

2 .

The processor will overheat without the heatsink and/or fan, resulting in perm anent

 

irreparable damage.

3 .

If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause im proper

installation. Please change the insert orientation.

4 . Apply thermal grease between the processor and cooling fan.

5 . Never run the processor without the heatsink properly and firmly attached . Perm anent damage will result.

6 . Please set the CPU host frequency in accordance with your processor's specifications. We don't recomm end you to set the system bus frequency over the CPU's specification because these specific bus frequencies are not the standard specifications for CPU, chipset and most of the peripherals. Whether your system can run under these specific bus frequencies properly will depend on your hardware configurations, including CPU, Memory, Cards… etc.

HT functionality requirement content :

Enabling the functionality of Hyper - Threading Technology for your com puter system requires all of the following platform components:

-CPU: An Intel® Pentium 4 Processor with HT Technology

-Chipset: An Intel® Chipset that supports HT Technology

-BIOS: A BIOS that supports HT Technology and has it enabled

-OS: An operation system that has optim izations for HT Technology

8I845PE-RZ Series Motherboard

- 8 -

Image 8
Contents 8I845PE-RZ / 8I845PE-RZ-C Feb.20 Installing the motherboard to the chassis Preparing Your ComputerTable of Contents Features Summary Introduction8I845PE-RZ Series Motherboard Layout 8I845PE-RZBlock Diagram EnglishStep Hardware Installation ProcessInstall the Central Processing Unit CPU CPU Installation Install Memory Modules DDRInstall AGP Card Install I/O Peripherals CablesCdin MIC In jackLAN port ~ USB portCpufan CPU Fan Connector ATX12V +12V Power ConnectorAtxatx Power FDD Floppy Connector Sysfan System Fan ConnectorIDE1 / IDE2 IDE1 / IDE2 Connector Fpanel 2 x 10 pins Connector Cdin CD In Connector Faudio Front Audio ConnectorSurcen Surround Center Connector Auxin AUX In Connector Spdifio Spdif In/Out ConnectorFUSB1 / FUSB2 Front USB Connector Clrcmos Clear CmosMain Menu Main Menu For example Bios Ver. FacStatus Page Setup Menu / Option Page Setup Menu Advanced Bios Features PowerManagement SetupPnP/PCI Configuration Load Fail-Safe DefaultsStandard Cmos Features DateTime IDE Primary Master, Slave / IDE Secondary Master, SlaveFloppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryAdvanced Bios Features First / Second / Third Boot DeviceBoot Up Floppy Seek PasswordCheckIntegrated Peripherals Onboard H/W LAN Boot ROM Parallel Port ModeUSB Controller USB Keyboard SupportPower Management Setup Resume by Alarm Power On By MousePower On By Keyboard KB Power on PasswordPnP/PCI Configurations PCI 1/PCI 5 IRQ AssignmentPCI 2 IRQ Assignment PCI 3 IRQ AssignmentPC Health Status Frequency/Voltage Control CPU Clock RatioCPU Host Clock Control CPU Host Frequency MHzTop Performance Host/DRAM Clock RatioMemory Frequency Mhz PCI/AGP FrequencyMhzLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password ConfigurationsEnter PasswordSave & Exit Setup Exit Without SavingInstall Drivers Pictures below are shown in Windows XPItem Description Memo English English Contact US