Intel 4112, 4127 user manual Set Supervisor/User Password

Page 51

2-12	Set Supervisor/User Password

	CMOS Setup Utility-Copyright (C) 1984-2007 Award Software
`	Standard CMOS Features	Load Fail-Safe Defaults
`	Advanced BIOS Features	Load Optimized Defaults
`	Integrated Peripherals	Set Supervisor Password
`	Power Management Setup	Set User Password
`	PnP/PCI ConfigurationsEnter Password:	Save & Exit Setup
`	PC Health Status	Exit Without Saving
`	Frequency/Voltage Control
ESC: Quit		KLJI: Select Item
F8: Q-Flash		F10: Save & Exit Setup
	Change/Set/Disable Password

Press <Enter> on this item and type the password with up to 8 characters and then press <Enter>. You will be requested to confirm the password. Type the password again and press <Enter>.

The BIOS Setup program allows you to specify two separate passwords:

Supervisor Password

When a system password is set and the Password Check item in Advanced BIOS Features is set to Setup, you must enter the supervisor password for entering BIOS Setup and making BIOS changes.

When the Password Check item is set to System, you must enter the supervisor password (or user password) at system startup and when entering BIOS Setup.

User Password

When the Password Check item is set to System, you must enter the supervisor password (or user password) at system startup to continue system boot. In BIOS Setup, you must enter the supervisor password if you wish to make changes to BIOS settings. The user password only allows you to view the BIOS settings but not to make changes.

To clear the password, press <Enter> on the password item and when requested for the password, press <Enter> again. The message "PASSWORD DISABLED" will appear, indicating the password has been cancelled.

- 51 -

BIOS Setup

Image 51

Contents GA-945GCM-S2L/ GA-945GCM-S2C Motherboard Identifying Your Motherboard Revision CopyrightDisclaimer Documentation ClassificationsTable of Contents Regulatory Statements Box Contents GA-945GCM-S2L/GA-945GCM-S2C Motherboard Layout Block Diagram Installation Precautions Hardware InstallationCPU Product Specifications4 Mbit flash Page Installing the CPU Installing the CPU and CPU CoolerCPU Socket Lever Installing the CPU Cooler Dual Channel Memory Configuration Installing the MemoryInstalling a Memory Installing an Expansion Card Back Panel Connectors Line In Jack Blue Line Out Jack GreenMic In Jack Pink Pwrled Internal ConnectorsGND CPUFAN/SYSFAN Fan Headers FDD Floppy Disk Drive ConnectorSATAII0/1/2/3 Sata 3Gb/s Connectors, Controlled by ICH7 IDE IDE ConnectorBatbattery Pwrled System Power LED HeaderFpanel Front Panel Header Faudio Front Panel Audio Header Cdin CD In ConnectorFUSB1/FUSB2 USB Headers Spdifo S/PDIF Out HeaderCI Chassis Intrusion Header Clrcmos Clearing Cmos JumperGA-945GCM-S2L/S2C Motherboard Bios Setup Startup Screen Following screen may appear when the computer bootsSample Bios Version GA-945GCM-S2L E10 Bios Setup Program Function KeysMain Menu „ PnP/PCI Configurations „ Standard Cmos Features„ Advanced Bios Features „ Power Management SetupIDE Channel 2, 3 Master/Slave DateTime IDE Channel 0 Master/SlaveMemory Floppy 3 Mode SupportDrive a Halt onHDD S.M.A.R.T. Capability Hard Disk Boot PriorityFirst/Second/Third Boot Device Password CheckCPU Thermal Monitor 2 TM2 Note Limit Cpuid Max. to 3 NoteNo-Execute Memory Protect Note CPU Enhanced Halt C1ENoteSata Port 0/2 Set to On-Chip Sata ModeOn-Chip Primary PCI IDE Pata IDE Set toUSB Keyboard Support Sata Port 1/3 Set toUSB Controller USB 2.0 ControllerSmart LAN Smart LAN LAN Cable Diagnostic FunctionOnboard Serial Port Onboard LAN Boot ROMParallel Port Mode ECP Mode Use DMAPower On by Ring Soft-Off by PWR-BTTNPME Event Wake Up Power On By Keyboard Resume by AlarmHpet Mode Note Power On By MousePnP/PCI Configurations PCI1 IRQ AssignmentPCI2 IRQ Assignment Case Opened Reset Case Open StatusCurrent CPU Temperature CPU Warning TemperatureCPU Smart FAN Control CPU Clock Ratio Note FSB1333 Core 2 CPUCPU Host Clock Control Memory Frequency Mhz CPU Host Frequency MhzPCI Express Frequency Mhz System Memory MultiplierLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstalling Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationGA-945GCM-S2L/S2C Motherboard Xpress Recovery2 Before You BeginSystem Requirements Installing Windows XP and Partitioning the Hard Drive Installation and ConfigurationPage Using the Backup Function in Xpress Recovery2 Accessing Xpress Recovery2Using the Restore Function in Xpress Recovery2 Removing the BackupExiting Xpress Recovery2 Updating the Bios with the Q-Flash Utility Bios Update UtilitiesUpdating the Bios Press Y to load Bios defaults Updating the Bios with the @BIOS Utility Installing and Using @BIOSOptions and Instructions Update the Bios without Using the Internet Update Function EasyTune 5 Interface Button Information Table EasyTuneWindows Vista ReadyBoost Configuring Audio Input and Output Configuring 2/4/5.1-Channel AudioConfiguring Speakers Speakers or Headphones Configuring Sound Effect Activating an AC97 Front Panel Audio ModuleMuting the Back Panel Audio For HD Audio Only Installing the S/PDIFOut Cable Optional Installing the S/PDIF Out CablePdif out Configuring S/PDIF out Configuring Microphone Recording Appendix Using the Sound Recorder Recording the SoundPlaying the Sound Frequently Asked Questions TroubleshootingStart Troubleshooting ProcedureEND Weee Symbol Statement Regulatory NoticesOur Commitment to Preserving the Environment China Restriction of Hazardous Substances Table GA-945GCM-S2L/S2C Motherboard B.T. INC USA Mexico Contact UsGigabyte Global Service System