JBL AVR 140 owner manual Speaker Selection, Speaker Placement

Page 15

Installation and Connections

Speaker Selection

No matter which type or brand of speakers is used, the same model or brand of speaker should be used for the front-left, center and front-right speakers. This creates a seamless front soundstage and eliminates the possibility of distracting sonic disturbances that occur when a sound moves across mismatched front-channel speakers.

Speaker Placement

The placement of speakers in a multichannel home-theater system can have a noticeable impact on the quality of sound reproduced.

Depending on the type of center-channel speaker in use and your viewing device, place the center speaker either directly above or below your TV, or in the center behind a perforated front-projection screen.

Once the center-channel speaker is installed, position the left-front and right-front speakers so that they are as far away from one another as the center-channel speaker is from the preferred listening position. Ideally, the front-channel speakers should be placed so that their tweeters are no more than 60cm above or below the tweeter in the center-channel speaker.

They should also be at least 0.5 meter from your TV set unless the speakers are magnetically shielded to avoid colourings on the TV screen. Note that most speakers are not shielded, even with complete surround sets only the Center speaker may be.

Depending on the specifics of your room acoustics and the type of speakers in use, you may find that imaging is improved by moving the front-left and front-right speakers slightly forward of the center-channel speaker. If possible, adjust all front loudspeakers so that they are aimed at ear height when you are seated in the listening position.

Using these guidelines, you’ll find that it takes some experimentation to find the correct location for the front speakers in your particular installation. Don’t be afraid to move things around until the system sounds correct. Optimize your speakers so that audio transitions across the front of the room sound smooth.

When the AVR is used in 5.1-channel operation, the preferred location for surround speakers is on the side walls of the room, at or slightly behind the listening position. In a 6.1-channel system, a back surround speaker is required, ide- ally placed at the center of the room's rear wall, pointing directly towards the front center chan- nel speaker. The center of the speaker should face you (see below).

As with the side speakers, rear surround speakers should be located so that the bottom of the cabinet is at least two feet higher than the listeners’ ears. The speakers should be no more than six feet behind the rear of the seating area.

Subwoofers produce largely nondirectional sound, so they may be placed almost anywhere in a room. Actual placement should be based on room size and shape and the type of subwoofer used. One method of finding the optimal location for a subwoofer is to begin by placing it in the front of the room, about 15cm from a wall, or near the front corner of the room. Another method is to temporarily place the subwoofer in the spot where you will normally sit, and then walk around the room until you find a spot where the subwoofer sounds best. Place the subwoofer in that spot. You should also follow the instructions of the subwoofer’s manufacturer, or you may wish to experiment with the best location for a subwoofer in your listening room.

A)Front Channel Speaker Installation with Direct-View TV Sets or Rear-Screen Projectors

5.1-Channel System

6.1-Channel System

At least 15 cm from celling

At least 60 cm

INSTALLATION AND CONNECTIONS 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents AVR 140 Audio/Video Receiver Declaration of Conformity Table of ContentsDescription and Features IntroductionFront panel analog A/V inputs Safety Information Important Safety InformationUnpacking Front Panel Controls Headphone Jack $Speaker/Channel Input Indicator# Preset Stations Selector Press this Digital Input Selector When playing aMore information on digital audio Digital Audio Rear Panel ConnectionsSurround Left Blue Surround Right Gray Surround Back Left Surround Back Right Tan Subwoofer LFEUnswitched Outlet Digital Audio Outputs Connect theseDigital recorder such as a CD-R or MiniDisc recorder Main Remote Control Functions › Button Speaker Select Mute Volume Up/DownSpare Button See page 31 for more information Channel/8 Channel Direct InputOptional is connected to Digital Media Player DMPInstallation and Connections Audio Equipment ConnectionsVideo Equipment Connections Scart A/V Connections Watts System and Power ConnectionsAC Power Connections CommandSpeaker Selection Speaker PlacementFirst Turn On System ConfigurationUsing the On-Screen Display System SetupCursor is next to the line reading Input SetupSurround Setup Navigation Button‹/› Navigation Buttons E Setting to your tasteNight Mode Settings ¤ Button Dso that the cursor is next toStereo-Direct Bypass Mode Configuring the Surround Off Stereo ModesStereo-Digital Mode Indicators is lit you are in the Stereo-Direct Bypass modeSpeaker Setup Screen menu That option press the ‹ / › Buttons EWithin five seconds, either press the ‹/› buttons Delay SettingsOutput Level Adjustment Button FNavigation Button E to enter Is then pressed to select OFF in the highlighted video Volume until you can hear the test noise clearly Conventional stereo recordings Surround Mode ChartOperation ChannelHall Channel/8-Channel Direct Input Controls and Use of HeadphonesBasic Operation Source SelectionDolby Digital Surround Mode SelectionDigital Audio Playback Until Surr OFF appears in the Main Information Display ÒPCM Audio Playback Surround Mode TypesDigital Bitstream Indicators Rear panel Or front panel *ÓSpeaker/Channel Indicators PCM Playback IndicationsSee Figure Tape Recording UsingOutput Level Adjustment With Source Signals Night ModeMemory Backup Front-Panel-Display FadeCursor next to the desired item, or place Full-OSD Time Out Adjustment Advanced FeaturesTurn On Volume Level Semi-OSD SettingsBasic Tuner Operation Default Surround ModeTuner Operation Full-OSD Background ColorProgram Search PTY RDS TuningRDS Operation RDS Display OptionsDirect Code Entry Programming the RemoteProgramming the Remote with Codes Code ReadoutVolume Punch-Through Macro ProgrammingProgrammed Device Functions By the AVR Input Selector Resetting the Remote MemoryChannel Control Punch-Through 4and the Mute buttonAM/FM Function ListAVR DVD Remote sensor Úis obscured Troubleshooting GuideProcessor Reset Power Switch 1is pushedTechnical Specifications Appendix Settings Worksheet Introduction Harman Consumer Group International

AVR 140 specifications

The JBL AVR 140 is an audio receiver that brings the excitement of a cinematic experience right into your living room. Designed with a sleek and modern aesthetic, this receiver combines advanced technology with user-friendly features, making it an excellent choice for both audiophiles and casual users.

One of the standout features of the AVR 140 is its impressive power output. This receiver delivers an impressive 100 watts per channel at 8 ohms, ensuring that it can easily drive large speakers and fill any room with high-quality sound. Its ability to reproduce audio with clarity and depth makes it a popular choice for home theater setups.

The AVR 140 is equipped with a range of audio formats that cater to various listening preferences. It supports Dolby Digital, DTS, and Pro Logic II, allowing users to immerse themselves in multi-dimensional soundscapes. This versatility ensures that whether you're watching movies, listening to music, or playing video games, the audio experience remains engaging.

Connectivity options are abundant with the JBL AVR 140. It features multiple HDMI inputs, allowing you to connect several devices such as Blu-ray players, gaming consoles, and streaming devices all at once. Additionally, it includes composite and component video inputs, ensuring compatibility with a wide variety of devices. The built-in AM/FM tuner also allows users to enjoy radio broadcasts without the need for additional equipment.

The AVR 140 incorporates advanced technologies that enhance the overall audio experience. One notable feature is the Audyssey setup, which calibrates the receiver based on your room's acoustics. This automatic calibration process optimizes speaker placement and ensures balanced sound across all channels.

With a user-friendly interface and an easy-to-navigate remote control, operating the JBL AVR 140 is straightforward. Its on-screen display helps guide users through various settings and configurations, making it accessible even for those who may not be technologically inclined.

In summary, the JBL AVR 140 is a versatile and powerful audio receiver that features a robust power output, support for multiple audio formats, extensive connectivity options, and advanced calibration technologies. Whether for movies, music, or gaming, it delivers an exceptional audio experience that elevates your entertainment setup to new heights. With its combination of quality, performance, and user-friendliness, the JBL AVR 140 stands out as a fantastic choice for anyone seeking to enhance their home audio experience.
Top Page Image Contents