JBL AVR 140 owner manual Advanced Features, Turn On Volume Level, Semi-OSD Settings

Page 34

Advanced Features

Turn On Volume Level

As is the case with most audio/video receivers, when the AVR is turned on, it will always return to the volume setting in effect when the unit was turned off. However, you may prefer to always have the AVR turn on at a specific set- ting, regardless of what was last in use when the unit was turned off. To change the default condition so that the same volume level is always used at turn-on, you will need to make an adjustment in the ADVANCED SELECT menu. To start the adjustment, press the OSD button Lto bring the MASTER MENU (Figure 1) to the screen. Press the ⁄ button D, until the on-screen ➞ cursor is next to the ADVANCED line. Press the Set button Fto enter the ADVANCED SELECT menu (Figure 11).

At the ADVANCED SELECT menu make certain that the on-screen ➞ cursor is next to the VOLUME DEFAULT line by pressing the ⁄/¤ buttons Das needed. Next, press

the › button so that the word ON is shown in the video display. Next, press the ¤ button Donce so that the on-screen › cursor is next to the DEFAULT VOL SET line. To set the desired turn-on volume, press the ‹/ › buttons E or hold them pressed until the desired volume level is shown on the DEFAULT VOL SET line. Note that this setting may NOT be made with the regular vol- ume controls.

NOTE: Since the setting for the turn-on volume cannot be heard while the setting is being made, you may wish to determine the setting before making the adjustment. To do this, listen to any source and adjust the volume to the desired

level using the regular volume controls . When the desired volume level to be used at turn-on is reached, make a note of the setting as it appears in the lower third of the video screen or in the Main Information Display Ò.

A typical volume level will appear as a negative number such as -25dB. When making the

adjustment, use the ‹/› buttons E

to

enter this setting.

 

Unlike some of the other adjustments in this menu, the turn-on volume default will remain in effect even when the unit is turned off completely, unless it is changed or turned off in this menu.

If you wish to make other adjustments in the menu, press the ⁄/¤ Buttons Duntil the on- screen ➞ cursor is next to the desired setting or the BACK TO MASTER MENU line and press the Set button F. If you have no other adjustments to make, press the OSD Button L to exit the menu system.

Semi-OSD Settings

The semi-OSD system places one line messages at the lower third of the video display screen whenever the Volume, Input Source, Surround mode or tuner frequency of any of the configura- tion settings are changed. The semi-OSD system is helpful in that enables you to have feedback on any control changes or remote commands using the video display when it is difficult to view the front-panel displays. However, you may occasionally prefer to turn these displays off for a particular listening session. You may also want to adjust the length of time the displays remain on the screen. Both of those options are possible with the AVR.

To turn off the semi-OSD system, you will need to make an adjustment in the ADVANCED SELECT menu (Figure 11). To start the adjustment, press the OSD button Lto bring the MASTER MENU to the screen. Press the

⁄Button D, until the on-screen➞ cursor is next to the ADVANCED line. Press the Set Button Fto enter the ADVANCED SELECT menu.

At the ADVANCED SELECT menu make certain that the on-screen ➞ cursor is next to the SEMI OSD line by pressing the ⁄/¤ but- tons Das needed. Next, press the › button

so that the word OFF is shown in the video display.

Note that this setting is temporary and will remain active only until it is changed or until the AVR is turned off. Once the unit is turned off, the semi-OSD displays will remain activated, even if they were switched off for the previous listening session.

To change the length of time that the semi-OSD displays remain on the screen, go to the ADVANCED SELECT Menu as outlined earlier, and press the ⁄/¤ buttons Das need- ed, until the on-screen ➞ cursor is next to the SEMI-OSD TIME OUT line. Next, press the ‹/› Buttons E until the desired time in seconds is displayed. Note that unlike most of the other options in this menu, this is a perma- nent setting change, and the time-out entry will remain in effect until it is changed, even when the unit is turned off.

If you wish to make other adjustments in the menu, press the ⁄/¤ Buttons Duntil the on- screen ➞ cursor is next to the desired setting or the BACK TO MASTER MENU line and press the Set button F. If you have no other adjustments to make, press the OSD Button L to exit the menu system.

Full-OSD Time Out Adjustment

The FULL OSD menu system is used to simplify the setup and adjustment of the AVR using a series of on-screen menus. The factory default setting for these menus leaves them on the screen for 20 seconds after a period of inac- tivity before they disappear from the screen or Time Out. This Time Out is a safety measure to prevent the menu text from burning into the CRTs in your monitor or projector, which might happen if they were left on indefinitely. However, some viewers may prefer a slightly longer or shorter period before the Time Out display.

To change the Full-OSD Time Out, you will need to make an adjustment in the ADVANCED SELECT menu (Figure 11). To start the adjustment, press the OSD button Lto bring the MASTER MENU to the screen. Press the

⁄button D, until the on-screen ➞ cursor is next to the ADVANCED line. Press the Set Button Fto enter the ADVANCED SELECT menu (Figure 11).

At the ADVANCED SELECT menu make certain that the on-screen ➞ cursor is next to the FULL OSD TIME OUT line by pressing the ⁄/¤ Buttons Das needed. Next, press the ‹/ › buttons E until the desired time is displayed in seconds. Note that unlike most of the other options in this menu, this is a perma- nent setting change, and the time-out entry will remain in effect until it is changed, even when the unit is turned off.

If you wish to make other adjustments in the menu, press the ⁄/¤ Buttons Duntil the on-screen ➞ cursor is next to the desired setting or the BACK TO MASTER MENU line and press the Set button F. If you have no other adjustments to make, press the OSD Button L to exit the menu system.

34INTRODUCTION / ADVANCED FEATURES

Page 33 Page 35
Image 34
Page 33 Page 35
Contents AVR 140 Audio/Video Receiver Table of Contents Declaration of ConformityIntroduction Description and FeaturesFront panel analog A/V inputs Important Safety Information Safety InformationUnpacking Headphone Jack $Speaker/Channel Input Indicator Front Panel ControlsDigital Input Selector When playing a # Preset Stations Selector Press thisMore information on digital audio Surround Back Right Tan Subwoofer LFE Rear Panel ConnectionsSurround Left Blue Surround Right Gray Surround Back Left Digital AudioDigital Audio Outputs Connect these Unswitched OutletDigital recorder such as a CD-R or MiniDisc recorder › Button Speaker Select Mute Volume Up/Down Main Remote Control FunctionsSpare Button Channel/8 Channel Direct Input See page 31 for more informationDigital Media Player DMP Optional is connected toAudio Equipment Connections Installation and ConnectionsVideo Equipment Connections Scart A/V Connections Command System and Power ConnectionsAC Power Connections WattsSpeaker Placement Speaker SelectionSystem Setup System ConfigurationUsing the On-Screen Display First Turn OnNavigation Button Input SetupSurround Setup Cursor is next to the line reading¤ Button Dso that the cursor is next to Setting to your tasteNight Mode Settings ‹/› Navigation Buttons EConfiguring the Surround Off Stereo Modes Stereo-Direct Bypass ModeIndicators is lit you are in the Stereo-Direct Bypass mode Stereo-Digital ModeSpeaker Setup That option press the ‹ / › Buttons E Screen menuDelay Settings Within five seconds, either press the ‹/› buttonsButton F Output Level AdjustmentNavigation Button E to enter Is then pressed to select OFF in the highlighted video Volume until you can hear the test noise clearly Channel Surround Mode ChartOperation Conventional stereo recordingsHall Source Selection Controls and Use of HeadphonesBasic Operation Channel/8-Channel Direct InputUntil Surr OFF appears in the Main Information Display Ò Surround Mode SelectionDigital Audio Playback Dolby DigitalRear panel Or front panel *Ó Surround Mode TypesDigital Bitstream Indicators PCM Audio PlaybackPCM Playback Indications Speaker/Channel IndicatorsSee Figure Night Mode UsingOutput Level Adjustment With Source Signals Tape RecordingFront-Panel-Display Fade Memory BackupCursor next to the desired item, or place Semi-OSD Settings Advanced FeaturesTurn On Volume Level Full-OSD Time Out AdjustmentFull-OSD Background Color Default Surround ModeTuner Operation Basic Tuner OperationRDS Display Options RDS TuningRDS Operation Program Search PTYCode Readout Programming the RemoteProgramming the Remote with Codes Direct Code EntryMacro Programming Volume Punch-ThroughProgrammed Device Functions 4and the Mute button Resetting the Remote MemoryChannel Control Punch-Through By the AVR Input SelectorFunction List AM/FMAVR DVD Power Switch 1is pushed Troubleshooting GuideProcessor Reset Remote sensor Úis obscuredTechnical Specifications Appendix Settings Worksheet Introduction Harman Consumer Group International

AVR 140 specifications

The JBL AVR 140 is an audio receiver that brings the excitement of a cinematic experience right into your living room. Designed with a sleek and modern aesthetic, this receiver combines advanced technology with user-friendly features, making it an excellent choice for both audiophiles and casual users.

One of the standout features of the AVR 140 is its impressive power output. This receiver delivers an impressive 100 watts per channel at 8 ohms, ensuring that it can easily drive large speakers and fill any room with high-quality sound. Its ability to reproduce audio with clarity and depth makes it a popular choice for home theater setups.

The AVR 140 is equipped with a range of audio formats that cater to various listening preferences. It supports Dolby Digital, DTS, and Pro Logic II, allowing users to immerse themselves in multi-dimensional soundscapes. This versatility ensures that whether you're watching movies, listening to music, or playing video games, the audio experience remains engaging.

Connectivity options are abundant with the JBL AVR 140. It features multiple HDMI inputs, allowing you to connect several devices such as Blu-ray players, gaming consoles, and streaming devices all at once. Additionally, it includes composite and component video inputs, ensuring compatibility with a wide variety of devices. The built-in AM/FM tuner also allows users to enjoy radio broadcasts without the need for additional equipment.

The AVR 140 incorporates advanced technologies that enhance the overall audio experience. One notable feature is the Audyssey setup, which calibrates the receiver based on your room's acoustics. This automatic calibration process optimizes speaker placement and ensures balanced sound across all channels.

With a user-friendly interface and an easy-to-navigate remote control, operating the JBL AVR 140 is straightforward. Its on-screen display helps guide users through various settings and configurations, making it accessible even for those who may not be technologically inclined.

In summary, the JBL AVR 140 is a versatile and powerful audio receiver that features a robust power output, support for multiple audio formats, extensive connectivity options, and advanced calibration technologies. Whether for movies, music, or gaming, it delivers an exceptional audio experience that elevates your entertainment setup to new heights. With its combination of quality, performance, and user-friendliness, the JBL AVR 140 stands out as a fantastic choice for anyone seeking to enhance their home audio experience.
Top Page Image Contents