Sanyo PLC-XW55G, PLC-XW50A, PLC-XW55A Lamp Handling Precautions, Lamp Replacement Counter

Page 55

Maintenance and Cleaning

Lamp Replacement Counter

Be sure to reset the Lamp replacement counter after the lamp is replaced. When the Lamp replacement counter is reset, the LAMP REPLACE indicator stops lighting.

1

Turn the projector on, press the MENU button to

 

 

display the On-Screen Menu. Press the Point 7

 

 

8 buttons to move the red framed pointer to the

 

 

Setting Menu icon.

 

2

Press the Point ed buttons to move the red

To reset the lamp counter,

 

framed pointer to the Lamp counter function and

 

then press the SELECT button. A dialog box

move the pointer to

 

appears showing the total accumulated lamp hours

Reset and then press the

 

SELECT button. “Lamp

 

and reset option. If you select "Reset", a "Lamp

 

replacement counter

 

replacement counter Reset?" message appears.

Reset?” dialog box is

 

Select [Yes] to continue.

displayed.

3

Another confirmation dialog box appears, select

Select [Yes],

then another

[Yes] to reset the Lamp replacement counter.

confirmation

box appears.

✔Note:

Do not reset the Lamp replacement counter without implementing lamp replacement. Be sure to reset the Lamp replacement counter only after replacing the lamp.

Select [Yes] again to reset the lamp counter.

LAMP HANDLING PRECAUTIONS

This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling may result in accidents, injury, or create a fire hazard.

●Lamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same life for each lamp. Some lamps may fail or terminate their life in a shorter period of time than other similar lamps.

●If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.

●A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.

IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN..

If a lamp explodes, disconnect the projector's AC plug from the AC outlet immediately. Contact an authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.

55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Multimedia Projector Features and Design Table of Contents Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsAir Circulation Installing the Projector in Proper PositionMoving the Projector Federal Communication Commission Notice ComplianceFront Back Bottom Part Names and FunctionsSlide Shutter Lever u Air Intake Vent Exhaust Vents Rear Terminal Top Control Remote Control Operating Range Remote Control Battery InstallationAdjustable Foot InstallationPositioning the Projector Projector side AC outlet side Connecting the AC Power CordCables used for connection Connecting to a ComputerConnecting to Video Equipment Connecting to Component Video Equipment PIN Code Input Dialog Box Selected Input Source and Lamp ModeBasic Operation Turning On the ProjectorTurning Off the Projector On-Screen Menu How to Operate the On-Screen MenuRemote Control Top ControlMenu Bar Keystone Correction Zoom AdjustmentScreen Position Adjustment Focus AdjustmentRemote Control Operation Sound AdjustmentKeystone button Timer buttonAuto PC button Zoom buttonsSource Select Menu Computer InputInput Source Selection Direct OperationSelecting Computer System Manually Computer System SelectionMenu Operation Auto PC Adj Auto PC AdjustmentTo store adjustment parameters PC Adjust MenuManual PC Adjustment To store adjusted data ResetMode free To clear adjusted dataImage Level Selection Image Level Adjustment Wide Screen Size AdjustmentNormal TrueDigital zoom + For zooming in and out the imagesDigital zoom Input Source Selection Video Video InputDirect Operation Top Control Input Source Selection S-Video, Component, RGB Scart 21-pinAV System Menu Component Video System SelectionAuto AV System Menu Video or S-VideoImage 1~4 CinemaTint ColorProgressive Noise reductionProvide the image at a normal video aspect ratio Setting SettingDisplay Logo Logo and Logo PIN code lock settingsLogo select Logo PIN code lock CaptureTo Enter the Logo PIN code Ceiling Rear CeilingRear Input searchPower management On start On start Remote controlKey lock Security Key lock and PIN code lock settingsPIN code lock Change the PIN code Change the PIN code lock settingFan Factory defaultLamp counter Then check the matters below Maintenance and CleaningSlide Shutter Cleaning the Air FiltersCleaning the Projector Cabinet Cleaning the Projection LensReset the lamp replacement counter Lamp ReplacementLamp Replacement Counter Lamp Handling PrecautionsAppendix TroubleshootingAppendix Menu Tree Image AdjustAppendix Video Input Indicators Indicators and Projector ConditionFreq Compatible Computer SpecificationsMechanical Information Technical SpecificationsOptional Parts Terminal Analog RGB Mini D-sub 15 pin Configurations of TerminalsTerminal Mini DIN 8-PIN PIN Code Number Memo Logo PIN Code Lock NoKR6AD

PLC-XW55G, PLC-XW55K, PLC-XW50A, PLC-XW55A specifications

The Sanyo PLC-XW55A, PLC-XW50A, PLC-XW55K, and PLC-XW55G are notable projectors designed to meet the demanding needs of both business and educational environments. These models are characterized by their high brightness, impressive resolution, and advanced features, making them suitable for various applications, from large conference rooms to classrooms.

One of the standout features of these projectors is their brightness. With up to 5,000 ANSI lumens, they are capable of delivering clear and vibrant images even in well-lit environments. This high brightness level ensures that presentations remain visible and impactful, regardless of ambient light conditions. Additionally, these models support XGA resolution (1024 x 768), providing clarity and detail that enhances the viewing experience.

The Sanyo PLC-XW55A and its variants utilize advanced LCD technology, which enriches colors and improves image sharpness. This technology helps to produce sharp, vivid images that effectively capture the audience's attention. Moreover, they offer a high contrast ratio, which contributes to deeper blacks and brighter whites, resulting in an overall enhanced visual experience.

Another key characteristic of these projectors is their versatility in connectivity options. Equipped with multiple inputs, including HDMI, VGA, and composite video, they accommodate a wide range of devices, such as laptops, Blu-ray players, and document cameras. This flexibility enables seamless integration into various audio-visual setups.

In terms of design, the Sanyo PLC-XW55 series projectors are compact and lightweight, which adds convenience for portability. Their user-friendly interface, along with remote control operation, simplifies setup and user experience. Furthermore, the projectors support vertical and horizontal keystone correction, allowing for easy adjustment of image distortion, ensuring a properly aligned projection even when the projector is not perfectly centered.

Finally, these projectors incorporate eco-friendly features, such as energy-efficient lamp technology, extending lamp life and reducing total cost of ownership. With an estimated lifespan of up to 4000 hours, users can minimize the frequency of replacements, making these models not only a practical choice but also a cost-effective one.

Overall, the Sanyo PLC-XW55A, PLC-XW50A, PLC-XW55K, and PLC-XW55G projectors stand out for their combination of brightness, resolution, connectivity, and ease of use, positioning them as ideal solutions for a range of professional and educational settings.
Top Page Image Contents