Sanyo DSU21B, DSU21E, DSU21N owner manual Safety Instructions, EN-3

Page 5

Safety Instructions

All the safety and operating instructions should be read before the product is operated.

Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

Follow all warnings and instructions marked on the projector.

For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.

Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers.

An appliance and cart combination should be moved

with care. Quick stops, excessive force, and uneven surfaces may cause the

appliance and cart combination to overturn.

Slots and openings in the back and bottom of the cabinet are provided for ventilation, to ensure reliable operation of the equipment and to protect it from overheating.

The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.

This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.

Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that

could result in a fire or electric shock. Never spill liquid of any kind on the projector.

Do not install the projector near the ventilation duct of air-conditioning equipment.

This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it.

Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions:

aWhen the power cord or plug is damaged or frayed.

bIf liquid has been spilled into the projector.

cIf the projector has been exposed to rain or water.

dIf the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.

eIf the projector has been dropped or the cabinet has been damaged.

fWhen the projector exhibits a distinct change in performance-this indicates a need for service.

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

EN-3

Image 5
Contents PDG-DSU21N/DSU21E/DSU21B Page EN-1 Safety PrecautionNotas acerca de pilas de Litio Solo CARIFORNIA, EE.UU EN-2Voor de klanten in Nederland Sanyo Fisher Sales Europe GmbHEN-3 Safety InstructionsAir Circulation Installing the Projector in Proper PositionEN-4 Moving the ProjectorEN-5 ComplianceEN-6 Contents EN-8 Projector FeaturesIntroduction Package Contents EN-10 Projector OverviewFront View EN-11 Rear ViewBottom View Control Panel Using the ProductButton Function EN-12RS-232C Connection PortsEN-13 EN-14 Remote ControlEN-15 Replacing the BatteryEN-16 Remote Control OperationEN-17 InstallationConnecting the Projector Powering On the Projector Powering On/Off the ProjectorPowering Off the Projector EN-18Adjusting the Projector Height Adjusting the ProjectorAdjusting the Projector Zoom and Focus EN-19EN-20 Adjusting Projection Image SizeEN-21 Menu OperationEN-22 How to operatePicture Computer / Video Mode EN-23 Aspect Ratio Video ModeImage White IntensityVideo Image Video Mode Computer Image Computer ModeSound Computer / Video Mode Setting Computer / Video ModeEN-25 Language Computer / Video ModeFactory Default Computer / Video Mode Cleaning the Lens MaintenanceCleaning the Projector Housing EN-26EN-27 Replacing the LampEN-28 Order Replacement LampEN-29 SpecificationsRemote Control Appendix LED Indicator MessagesEN-30 Optional PartsComputer Compatibility ModesVideo EN-31Start-up problems TroubleshootingImage problems Remote control problemsEN-33 Command FormatConnection and Operation Available button Icon Configuration of RS-232C TerminalEN-34 On the remote Functions ControlPage Part No AA6P1P5587--KA7AA