Hitachi CP-X2511N, CP-X3011N, CP-X4011N Shutting the projector down, Resetting all settings

Page 94

Troubleshooting

Regarding the indicator lamps (continued)

POWER LAMP TEMP indicator indicator indicator

Description

 

 

 

There is a possibility that the interior portion

 

 

 

has become heated.

Blinking

 

 

Please turn the power off, and allow the projector to cool down at least

 

 

20 minutes. After the projector has sufficiently cooled down, please make

In Red

 

 

Turned

Lighting

confirmation of the following items, and then turn the power on again.

or

off

In Red

• Is there blockage of the air passage aperture?

Lighting

 

 

• Is the air filter dirty?

In Red

 

 

 

 

• Does the peripheral temperature exceed 35°C?

 

 

 

If the same indication is displayed after the remedy, please set FAN

 

 

 

SPEED of SERVICE item in OPTION menu to HIGH (￿55).

 

 

 

It is time to clean the air filter.

Lighting

Simultaneous

Please immediately turn the power off, and clean or

change the air filter referring to the section “Cleaning

In Green

blinking in Red

and replacing the air filter”. After cleaning or changing

 

 

 

the air filter, please be sure to reset the filter timer.

 

 

 

After the remedy, reset the power to ON.

 

 

 

There is a possibility that the interior portion

Lighting

Alternative

has become overcooled.

Please use the unit within the usage temperature

In Green

blinking in Red

parameters (5°C to 35°C).

 

 

 

 

 

 

After the treatment, reset the power to ON.

 

 

 

 

Blinking In

 

 

At least 1 Power ON schedule is saved to the

Green for

Turned

Turned

projector.

approx. 3

off

off

Please refer to Schedule Settings section of User’s

seconds.

 

 

Manual - Network Guide.

NOTE • When the interior portion has become overheated, for safety purposes, the projector is automatically shut down, and the indicator lamps may also be turned off. In such a case, disconnect the power cord, and wait at least 45 minutes. After the projector has sufficiently cooled down, please make confirmation of the attachment state of the lamp and lamp cover, and then turn the power on again.

Shutting the projector down

Only when the projector can not be turned off by usual procedure (￿17), please push the shutdown switch using a pin or similar, and disconnect the power plug from the power outlet. Before turning it on again, wait at least 10 minutes to make the projector cool down enough.

Resetting all settings

Shutdown switch

HDMI

USB

When it is hard to correct some wrong settings, the FACTORY RESET function of SERVICE item in OPTION menu (￿59) can reset all settings (except settings such as LANGUAGE, LAMP TIME, FILTER TIME, FILTER MESSAGE, SECURITY and NETWORK) to the factory default.

94

Downloaded from www.Manualslib.com manuals search engine

Page 93 Page 95
Image 94
Page 93 Page 95
Contents CP-X2011N/CP-X2511N /CP-X3011N/CP-X4011N About this manualThank you for purchasing this projector Trademark acknowledgmentContents Features Checking the contents of packageProjector Part namesHOT LAN port Control panel STANDBY/ON buttonRear panel 9 ~ USB Type a port Audio OUT L,R portsDown button Volume + button Remote controlComputer button Arrangement Setting upOn a horizontal surface Suspended from the ceiling Arrangement Connecting with your devices About Plug-and-Play capabilityConnecting with your devices VCR/DVD/Blu-ray Disc Computer PlayerConnecting with your devices Monitor Microphone system SpeakersUSB storage Device Computer Access point Connecting to a power supply Using the security bar and slotAbout the remote control signal Remote controlInstalling the batteries Hitachi MAXELL, Part No.LR6 or R6PUsing as a simple PC mouse & keyboard Changing the frequency of remote control signalUSB port Turning off the power Power on/offTurning on the power STANDBY/ON buttonOperating Adjusting the volumeSelecting an input signal Temporarily muting the soundVideo button Press the MY Source / DOC. Camera button onComputer button MY SourceSelecting an aspect ratio Searching an input signalFor an Hdmi signal Search buttonAdjusting the projectors elevator Adjusting the zoom and focusUsing the automatic adjustment feature Adjusting the positionCorrecting the keystone distortions Keystone buttonUsing the magnify feature Magnify ON/OFF buttonFreeze button Temporarily freezing the screenTemporarily blanking the screen Blank buttonEasy Menu Using the menu functionReset button Advanced MenuIndication in OSD On Screen Display Indication MeaningNormal Cinema Dynamic Boardblack DescriptionDaytime Whiteboard Boardgreen Language ECO ModeMirror SecurityPicture menu GammaCustom SAVE-1, SAVE-2, SAVE-3, SAVE-4 Presentation Theater OFFActive Iris MY Memory LOAD-1,LOAD-2,LOAD-3,LOAD-4Image menu For a computer signalFor an Hdmi signal AspectPosition USB Type B or Hdmi portFrom the LAN, USB Type A, USB Type B or Hdmi port For a video signal and s-video signalFor a component video signal SizeHigh MID LOW Input menuTV Film OFF Component Scart RGBHdmi Format Video FormatHdmi Range Frame Lock Auto Sync on G OFFOn OFF Resolution Auto Keystone Setup menuKeystone Normal Saving Normal ECONormal Hinvert Vinvert H&VINVERT Monitor OUTAudio menu 480i@60 for COMPONENT, Computer IN1 or Computer IN2MIC Level MIC VolumeHdmi Audio High LOWBlank Screen menuEnglish Français Deutsch Español Start UPMyScreen Capturing error has occurred. Please try againMyScreen registration is finished Invalid Scan Freq No Input is DetectedSync is OUT of Range MessageUse the / buttons on the Screen menu to select Source Test Pattern DOT-LINE1 DOT-LINE2 DOT-LINE3 MAP2 MAP1 CIRCLE2 CIRCLE1 DOT-LINE4Mode Description Closed CaptionDisplay ChannelUSB Type B port Option menuAuto USB Type B OFFMouse USB Display Type B portCancel OK Lamp TimeMY Button X4011N Computer IN1 Computer IN2 LAN USB Type aFAN Speed ServiceAuto Adjust Ghost1NORMAL 2HIGH KEY LockRemote Freq Control portBaud Rate Serial SettingsCommunication Type ParityResponse Limit Time Transmission MethodFactory Reset InformationDynamic Host Network menuDhcp ConfigurationDifference AddressMask TimeProjector Name MY Image AMX D.DPresenter QuitPresentation Section Switching Guide Security menu If you have forgotten your passwordEnter the Security menu Turning off the MyScreen Password Turning on the MyScreen PasswordMyScreen Turning off the PIN Lock PIN LockTurning on the PIN Lock If you have forgotten your PIN codeTurning on the Transition Detector Transition DetectorTurning off the Transition Detector Turning on the MY Text Password MY Text PasswordTurning off the MY Text Password MY Text WritingSupported storage media Presentation toolsPC-LESS Presentation Supported formatThumbnail mode Down Setup menu for the selected imageOperating by buttons or keys Enter InputOperating by the menu on the Thumbnail screen PC-LESS Presentation DOWN, Right Down UP, LeftSlideshow mode Return Playlist Example of playlist.txt filesHardware and software requirement for computer USB DisplayUSB Port USB cable 1 piece Right-Click menu Transmission speed Keep PC resolutionOptimize Performance Image qualityType number DT01021 MaintenanceReplacing the lamp Replacing the lampHigh Voltage High Temperature High Pressure Lamp warningCleaning and replacing the air filter Type number MU06481 Filter setCleaning and replacing the air filter Replacing the internal clock battery Hitachi MAXELL, part number CR2032 or CR2032HInside of the projector Caring for the cabinet and remote controlOther care Caring for the lensRelated messages TroubleshootingMessage Description Internal temperature is rising Related messagesIndicator Regarding the indicator lampsPower Lamp Temp OffPower Lamp Temp indicator indicator indicator Description Resetting all settingsShutting the projector down Signal source does not correctly work Phenomenon Cases not involving a machine defectAudio SOURCE/SPEAKER setting is not correct Signal cables are not correctly connectedVolume is adjusted to an extremely low level Mode selected for Hdmi Audio is not suitableProjector is operating in Eco mode Color settings are not correctly adjustedColor Space setting is not suitable Freeze function is workingNetwork BridgeSpecifications SpecificationSpecifications End User License Agreement for the Projector Software

CP-X4011N, CP-X2511N, CP-X3011N specifications

The Hitachi CP-X3011N, CP-X2511N, and CP-X4011N are three prominent models in the lineup of projectors designed for educational and corporate environments. These projectors are celebrated for their reliability, performance, and advanced features, making them suitable for various presentation needs.

The CP-X3011N is characterized by a brightness of 3,100 lumens, which allows for clear and vibrant images even in well-lit environments. With a native XGA resolution of 1024 x 768, it delivers sharp images that are ideal for displaying detailed presentations and video content. The projector employs advanced technology such as a 3LCD system, which ensures accurate color reproduction and exceptional image quality. The lens operation is also notable, with a 1.2x optical zoom that provides flexibility in positioning.

In contrast, the CP-X2511N offers a slightly lower brightness at 2,600 lumens but maintains the same native XGA resolution. This projector is designed for environments where budget is a consideration while still providing excellent performance. It features a lightweight design, making it easily portable for on-the-go presentations. The CP-X2511N also incorporates energy-saving technology that helps reduce the overall power consumption, contributing to lower operational costs.

The CP-X4011N, on the other hand, stands out with a brightness of 4,200 lumens, making it one of the brightest models in this series. This makes it an excellent choice for larger venues or spaces with significant ambient light. The projector supports both XGA and WXGA resolutions, giving users the option for enhanced image detail with widescreen presentations.

All three models boast a variety of connectivity options, including HDMI, VGA, and USB ports, accommodating various devices and media formats. They also feature advanced networking capabilities for remote management, allowing IT administrators to monitor multiple projectors on a single platform.

Additionally, the projectors come equipped with a range of user-friendly features such as automatic keystone correction, which ensures images are aligned and distortion-free, and a quick start function that allows users to begin their presentations with minimal downtime.

With their robust performance and strategic feature set, the Hitachi CP-X3011N, CP-X2511N, and CP-X4011N projectors are designed to meet the demands of any professional presentation or educational setting.
Top Page Image Contents