Hitachi CP-S845W Do not step on this unit or do not put a Heavy object on it, Cleaning, Long time

Page 6
Pull out the power plug from the power outlet.

Caution

Do not step on this unit or do not put a

heavy object on it.

Do not step on this unit. Especially pay attention if children are present. If you do, the unit may fall over or may be broken causing an injury.

Do not put a heavy object on this unit. If you do, the unit may fall due to its imbalance or it may drop, causing an injury.

Do not block the ventilation holes.

Do not block the ventilation holes. If the ventilation holes are blocked, the heat inside may build up and it may cause a fire. Do not use this unit in the following ways: On its side. In a poorly ventilated, narrow place. On a carpet or bedspread. Covered with a tablecloth. Place this unit so that the ventilation holes are kept 30cm or more away from the wall.

Cleaning

Be sure to pull out the power plug

 

from the power outlet for safety

Pull out the power

when cleaning.

plug from the

power outlet.

Set the caster stoppers.

When this unit is installed on the table with casters, set the caster stoppers. If the table moves, it may fall over, causing an injury.

Do not place this unit in a moist or dusty place.

Do not place this unit in a moist or dusty place. It may cause a fire, electric shock, etc.

Do not place this unit where it would be exposed to soot or steam, near a cooking stove or humidifier, etc. It may cause a fire, electric shock, etc.

Handle the power cord carefully.

Do not bring the power cord near a heating device. The shield of the cord may melt and it may cause a fire, electric shock, etc.

Do not insert / disconnect the power plug with wet hands. It may cause an electric shock.

When the power plug is to be disconnected, do not pull the power cord. The power cord may be damaged and it may cause a fire, electric shock, etc. Be sure to hold the power plug.

Caution when carrying it.

When this unit is to be moved, apply a cover to the lens and be sure to disconnect the power plug from the power outlet and check that all external connection cords are removed before moving it. If not, the cord may be damaged and it may cause a fire, electric shock, etc.

Use of batteries.

When you are not going to use for a

• Do not use batteries not specified for

this unit. Do not use new batteries

mixed together with old ones. This

may cause a fire, injury due to

burst of battery, liquid leakage.

• When inserting batteries in this unit,

pay attention to the direction of the

and polarity indications and

long time.

When you are not going use this unit for a long time because you are going on a trip, etc., be sure to pull out the power plug from the power outlet for safety. And also apply cover to the lens so that the lens is not damaged.

Pull out the power plug from the power outlet.

insert the batteries correctly. If the

polarities are confused, it may

cause injury or damage near the

unit due to burst batteries, liquid

leakage, etc.

6

Clean inside the unit at least once two years.

Ask your dealer to clean inside the unit at least once two years. If the unit is left with too much dust inside as it is for a long this without cleaning, it may cause a fire. Especially it is effective to clean before the rainy season starts. Consult your dealer for the cost of the cleaning the inside the unit.

Downloaded from www.Manualslib.com manuals search engine

Image 6
Contents Outline FeaturesContents Operating GuideAbout Trademarks Before use Video signal cablesPower cord Instructions to UsersDo not use power supplies other Than that specified Do not look directly at the lens when Lamp is litDo not install this unit in an unstable place If any abnormality occursDo not stare directly into the laser aperture LASER-STRAHLUNG PlaceUse of batteries When you are not going to use for a CleaningHandle the power cord carefully Clean inside the unit at least once two yearsCleaning the lens Do not place this unit where it gets hotVolume Cleaning the cabinetContents of shipping box Names and functions of each partVideo input terminal Remote control sensor Main Power switchAC in socket RGB input terminalRemote control transmitter How to insert batteries Names and functions of each partInstallation Example of the projector and screen installationHow to use foot adjusters On indicator will light up orange Basic operationsTo project the picture Standby mode To turn off the powerIndicator lights up orange PLUG&PLAYFreeze Function Magnifying FunctionMemory function Adjustments and functionsTo return to the initial setting On-screen menus are displayed on the screenBar display items VOLUME, Bright etc SET UPHow to use the SET UP menu Numerical display items V POSIT, H Posit etcDuring AUTO-adjustment AUTO-adjustmentAUTO-adjustment Confirm Screen Adjustment Item Details of adjustmentOPT Image The menu Image serves of the picture inversionMenu OPT. allows you to control communication function etc Connection to the video signal terminals Connection to the RGB signal terminalExample of computer signal Resolution Standard Display Dots KHz TypeInitial set signals Computer/signal Horizontal Timing µsComputer/signal Vertical Timing lines Connection to the control signal terminal Control signal terminalPS/2 mouse ADB Mac mouseSerial mouse Communication Control command tableControl command table RS232C cable OptionCommand data Procedure of default setting the Projector status Procedure of getting the Projector statusProcedure of setting the Projector status Example of command errorAC Inlet Computer Note type Example of system setupConnecting various equipment ComputerDesk typeCleaning the air filter Air filter Filter coverDo not use with removed air filter If it is probable that the lamp has exploded Remove the lamp coverLoosen two screws and pull the handle to remove Lamp Loosen a screw and remove the coverLamp Install the lamp cover and fix it using screwsReset the lamp time MalfunctioningOn-screen display Indicator displayMessage table ActionWhen you think something wrong RCA Jack terminal Input terminal Input/Output Dimension diagramProduct name Liquid crystal projector Model name CP-S845W RCA Jack terminal Terminal
Related manuals
Manual 34 pages 52.32 Kb