NEC MT1065/MT1060 user manual Making Connections, When Viewing a DVI Digital Signal

Page 14

Making Connections

NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting with the projector.

*If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power management software.

*If you accidentally hit the POWER button on the remote control, wait 90 seconds and then press the POWER button again to resume.

When Viewing a DVI Digital Signal:

To project a DVI digital signal, be sure to connect the PC and the projector using a DVI-D signal cable (not supplied) before turning on your PC or projector. Turn on the projector first and select DVI (DIGITAL) from the source menu before turning on your PC.

Failure to do so may not activate the digital output of the graphics card resulting in no picture being displayed. Should this happen, restart your PC. Do not disconnect the DVI-D signal cable while the projector is running. If the signal cable has been disconnected and then re-connected, an image may not be correctly displayed. Should this happen, restart your PC.

NOTE:

Use the DVI-D cable compliant with DDWG (Digital Display Working Group) DVI (Digital Visual Interface) revision 1.0 standard. The DVI-D cable should be within 5 m (196") long.

The DVI (DIGITAL) connector accepts VGA (640x480), SVGA (800x600), 1152x864, XGA (1024x768) and SXGA (1280x1024 @ up to 60Hz).

Connecting Your PC or Macintosh Computer

DVI IN

RGB 2 IN

RGB 1IN

RGB signal cable (supplied) To mini D-Sub 15-pin connec-

tor on the projector. It is recom- mended that you use a com- mercially available distribution amplifier if connecting a signal cable longer than the supplied one.

DVI-D cable (not supplied)

Audio cable (not supplied)

IBM PC or Compatibles (Desktop type) or Macintosh (Desktop type)

PHONE

IBM VGA or Compatibles (Notebook type) or Macintosh (Notebook type)

Connecting your PC or Macintosh computer to your projector will en- able you to project your computer's screen image for an impressive pre- sentation.

To connect to a PC or Macintosh, simply:

1.Turn off the power to your projector and computer.

2.Use the supplied signal cable to connect your PC or Macintosh to the projector.

3.Turn on the projector and the computer.

4.If the projector goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer you've connected to the projector.

PHONE

NOTE: For older Macintosh, use a commercially available pin adapter (not supplied) to connect to your Mac's video port.

Connecting to RGB 2 IN connectors

Use a BNC×5 cable to connect your PC and the RGB 2 IN connectors on your projector.

Connecting Your PC with a DVI Connector

Use a DVI-D signal cable (not supplied) to connect a DVI connector of your PC to the projector.

NOTE: The MT1065/MT1060 is not compatible with video decoded outputs of NEC ISS-6020 and ISS-6010.

E-14

Image 14
Contents MT1065/MT1060 Safety Cautions Guarantee policy Fire and Shock PrecautionsLamp Replacement Whats in the Box?Table of Contents Introduction to the Projector Features youll enjoyIntroduction Carrying the Projector Part Names of the ProjectorAttaching the lens cap Top Features SelectTerminal Panel Features Part Names of the Remote Control On the screen using the SelectRGB Viewer Operating Range for Wireless Remote Control Battery InstallationRemote Control Precautions Using the Remote Control in Wired OperationSelecting a Location Installation and ConnectionsSetting Up the Screen and the Projector Throw Distance and Screen Size Distance ChartDo not attempt to install the projector yourself Reflecting the ImageConnecting to RGB 2 in connectors When Viewing a DVI Digital SignalConnecting Your PC or Macintosh Computer Connecting Your PC with a DVI ConnectorConnecting an External Monitor To connect Scart output RGBConnecting Your DVD Player DVD playerConnecting Your VCR or Laser Disc Player Connecting the Supplied Power CableProjecting AN Image Basic Operation Turning on the ProjectorAdjust the Tilt Foot Adjusting the Picture Size and PositionUsing the Remote Control Selecting a SourceFocus When using the USB connected to the projectorUsing Auto Focus Use the Focus Button +/- to obtain the best focusWhen using the remote control or cabinet buttons Confirmation screen is displayedAdjusting the Image Using Auto Adjust Turning Up or Down VolumeUsing the Laser Pointer Optimizing RGB Picture AutomaticallyTo turn off the projector Setting the function switchTurning off the Projector Convenient Features Using the Remote Mouse FunctionGetting the On-line Help Using the PointerFreezing a Picture Using the USB Mouse Using the USB HUB Function Operate the Menus using the USB mouseChanging Background Logo Making Freehand Drawings on a Projected Image ChalkBoardUsing the Viewer Making the Most out of the Viewer FunctionProjecting slides Viewer When the tool bar is not displayedOperating the Viewer Function from the Projector playback Viewing Digital Images Auto Play ModeSwitching to Slides Directly from Other Input Modes PreparationsTo delete captured images Using the PC Card Files Fucntion PC Card FilesDeleting Captured Images Default Custom Menu items are Using ON-SCREEN MenuUsing the Menus Basic Menu OperationMenu tree Advanced MenuCommunication Speed Operation Mode SelectDefault Source Select WEP Menu Elements Source Select Entering Alphanumeric Characters by Using the MenuMenu Descriptions & Functions Sound Entry Edit CommandPicture not available for Viewer and LAN Image OptionsPicture Management Projector Options Using Adapting Color Correction Wall Color Correction Button to move the yellow box to select a Menu Setup User can adjust the image display functions Hori Resolution manuallySelecting Lamp Mode and Lamp Type Lamp Setting Selecting Aspect Ratio and Position for Screen Screen Selecting Auto FunctionsSetting LAN Mode Network Type required for wireless onlyUses 64-bit datalength for secure transmission WEP for Wireless onlyNications may be monitored by someone Pared to use of 64bit datalength encryptionEntry Setting a PasswordStatus DeleteTo delete PC card data you registered To enable Security, use the SelectSecurity Help Returning to Factory DefaultTools To replace the lamp MaintenanceReplacing the Lamp Cleaning the Cabinet and the Lens CleaningCleaning or Replacing the Filter Vacuum the filter-through the filter coverStatus Indicator TroubleshootingPower Indicator Lamp IndicatorContents of PC Card are damaged Common Problems & Solutions Check These ItemsWhen using the Viewer function Image isn’t square toSpecifications Model Number MT1065/MT1060 OpticalMini D-Sub 15 Pin Connector Cabinet DimensionsPin Assignments of D-Sub RGB Input Connector Pin No RGB Signal Analog YCbCr SignalCompatible Input Signal List PC Control Codes and Cable Connection PC Control Connector D-SUB 9PUsing Software Keyboard Cable ConnectionPreparation Before Use Operation Using an Http BrowserOverview Handling of the Address for Operation via a BrowserTerm of warranty TravelCare a service for international travelersServices offered with TravelCare TravelCare GuideAsia and Middle East Abba Electronics L.L.CApplication Sheet for TravelCare Service Program Condition of your TravelCare Service Program

MT1065/MT1060 specifications

The NEC MT1065 and MT1060 are advanced portable projectors that exemplify high-quality performance for various professional settings. These models, part of NEC’s reputation for reliable display solutions, cater to a wide range of applications, from corporate presentations to educational environments. Both projectors share several key features and technologies that make them standout choices in the market.

One of the main characteristics of the MT1065 and MT1060 is their high brightness level. The MT1065 delivers an impressive 5,500 ANSI lumens, while the MT1060 offers a slightly lower luminous output at 4,500 ANSI lumens. This high brightness ensures that presentations remain clear and visible, even in well-lit rooms. The projectors feature a high contrast ratio that enhances image quality by producing deeper blacks and brilliant whites.

In terms of imaging technology, both models utilize DLP (Digital Light Processing) technology, which is renowned for its sharpness and color accuracy. DLP technology contributes to vibrant images with smooth transitions and little to no motion blur, making these projectors suitable for displaying video content, graphics, or text-heavy presentations.

Portability is another vital aspect of the NEC MT1065 and MT1060. Weighing just over 6.5 lbs each, these projectors are designed for ease of transport, making them ideal for business professionals who frequently move between different locations. Their compact size does not compromise their durability, as they are constructed with robust materials suitable for various environments.

Both models come equipped with multiple connectivity options, including HDMI, VGA, and USB ports. This versatility allows users to connect a wide range of devices, from laptops and tablets to USB thumb drives, providing flexibility in presentations. Furthermore, the projectors also support a variety of display resolutions, up to Full HD 1080p, ensuring compatibility with modern multimedia content.

User-friendliness is emphasized through features such as automatic keystone correction and an intuitive user interface, simplifying setup and operation. The projectors also incorporate energy-efficient technologies, reducing power consumption and contributing to lower operational costs.

In summary, the NEC MT1065 and MT1060 projectors are equipped with high brightness levels, advanced DLP imaging technology, and user-friendly features, making them excellent choices for professionals seeking reliable, high-performance portable projectors. With their solid build quality and versatility, they effectively meet the demands of dynamic presentation environments.