NEC MT 1020G /820G user manual P E R a T I O N

Page 22

3 O P E R A T I O N

This section describes how to select a computer or video source and how to adjust the picture and sound.

General Controls Before you turn on your MultiSync MT1020G/820G LCD Projector, ensure that the computer or video source is turned on and that your lens cap is removed.

1.Turn On The LCD Projector The main power switch is on the back panel of the MultiSync MT1020G/820G LCD Projector. By turning this switch on, the projector will go into its standby mode and the power light will glow amber. Only after you press the "On" button on the remote control or projector cabinet will the power light turn to green and the projector become ready to use.

NOTE: To turn the LCD projector on and off with just the back panel switch, use the menu and enable the "auto

start" feature. (See page E-26. )

2.Select The Computer Or Video Source Press the "Video" (VCR, document camera, or laser disc player), "S-video", "RGB 1" or "RGB 2" (computer) button on the remote control to display the image. Or press the "Menu" button on the cabinet and use the icons to select your video source: "Video", "S-Video", "RGB 1" or "RGB 2."

3.Adjust The Image Size Press the "Zoom" button (+) or (–) on the remote control or projector cabinet to make the image larger or smaller.

4.Focus Press the "Focus" button (+) or (–) on the remote control or projector cabinet to focus the image.

5.Turning Off The Projector First press the "off" button on the remote control or the projector cabinet. The power light will glow amber. Then turn off the main power switch on the back panel. The power light will go out.

IMPORTANT:

•The LCD projector should be unplugged if it will not to be used for an extended period.

•To turn off the image briefly (five minutes or less), use the "Picture Mute" button instead of turning the projector off and on.

•The LCD projector will display a black, blue, or loop image if no input signal is present.

•Do not turn the LCD projector off and then immediately back on. The projector needs to cool for a minute before it can be restarted.

E – 22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents MultiSync MT 1020G /820G LCD Projector User’s Manual Precautions Cleaning InstallationPower Supply Lamp ReplacementB L E O F C O N T E N T S Features you’ll enjoy include N T R O D U C T I O NHow Do You Get Started? What’s In The Box?Rear Features Front FeaturesRight Side Features Left Side Features Top Features Terminal Panel Features 9RGB Monitor Output Connector Mini D-Sub 15 pin 6RGB Input 1 Connector D-Sub 15 pin7RGB Input 2 Connector Mini D-Sub 15 pin RGB 1 Audio Input Mini JackRemote Control Features Remote Control Precautions Setting Up Your MultiSync MT1020G/820G LCD Projector InstallationUsing the Supplied Lift Kit Using a Tabletop Or Cart Side viewReflecting The Image Ceiling InstallationRear Screen Projection Wiring Diagram Connecting Your PC Or Macintosh Computer Windows MacintoshConnecting Your VCR Or Laser Disc Player Connecting Your Document CameraConnecting An External Monitor Connecting Your Remote Mouse Receiver Remote Mouse Receiver as a mouse for your computer P E R a T I O N Using The Menus Menu Descriptions & Functions Fine Picture** when Auto Picture is off Image ModePicture Adjustment** when Auto Picture is off Power MenuImage Loop Settings MenuCustom Memory BackgroundReset LanguageTo replace the lamp A I N T E N a N C EReplacing The Lamp StepCleaning Or Replacing The Filter Remote Control Battery InstallationTroubleshooting Status Light MessagesCommon Problems & Solutions Problem Check These ItemsElectrical Specification SOptical MechanicalDimensions PC 15-Pin mini D-Sub Macintosh 15-Pin D-Sub Sub Pin AssignmentsPC 15-Pin mini D-Sub Timing Chart Yes/No Signal Resolution Refresh Dot Rate Hz KHz ClkMHzPC Control Command Reference Command Codes Function Code Data DescriptionPC Control Connector DIN-8P Cable Connection Communication Protocol
Top Page Image Contents