NEC VT480, VT57, VT58 manual Adjusting the Picture Size and Position, Adjust the Tilt Foot

Page 30

3. Projecting an Image (Basic Operation)

Adjusting the Picture Size and Position

Place your projector on a flat level surface and ensure that the projector is square to the screen.

Lift the front edge of the projector to center the image vertically.

* If the projected image does not appear square to the screen then use the Keystone feature for proper adjustment. (page 24)

Move the projector left to center the image horizontally on the screen.

Adjust the Tilt Foot

1. Lift the front edge of the projector.

CAUTION:

Do not try to touch the ventilation outlet during Tilt Foot adjustment as it can become heated while the projector is turned on and during its cool down period after it is turned off.

Adjustable Tilt Foot Button

1

PUSH

2.Push and hold the Adjustable Tilt Foot Button on the front of the projector to extend the adjustable tilt foot.

3.Lower the front of the projector to the desired height.

4.Release the Adjustable Tilt Foot Button to lock the Adjustable tilt foot.

There is approximately 10 degrees (up) of adjustment for the front of the projector.

Adjusting the height of a projected image or changing projection angle will run the Auto Keystone correction function to quickly correct the vertical distortion. The "Keystone" screen will be displayed.

For operating the "Keystone" screen, see " Correcting Keystone Distortion" on page 24.

The rear foot height can be adjusted up to 0.4 inch/10 mm.

Rotate the rear foot to the desired height in order to square the image on the projection surface, but the vertical distance from the bottom to the desk or floor should be 0.4 inch /10mm to make the projector horizontal on the flat surface.

NOTE: If you rotate the rear foot too much, it will come off from the bottom.

2

Adjustable Tilt Foot

 

4

 

3

S-

 

VIDEO

 

IN

 

 

L

 

PCC

 

ONTROL

 

MONITOR

VIDEOIN

OUT(COMP1)

 

AUDIOIN

 

COMPUTER1IN

 

AUDIOOUT

 

COMPUTER2IN

Up

Down

CAUTION:

Do not use the tilt-foot for purposes other than originally intended. Misuses such as using the tilt foot to carry or hang (from the wall or ceiling) the projector can cause damage to the projector.

Up

Down

22

Image 30
Contents VT580/VT480/VT58/VT57/VT48 Page DOC Compliance Notice for Canada only Safety CautionsPrecautions Disposing of your used productImportant Information Important SafeguardsInstallation RF Interference for USA onlyFire and Shock Precautions IiiRemote Control Precautions Lamp ReplacementLamp Characteristic Table of Contents Using On-Screen Menu Table of ContentsConvenient Features MaintenanceWhats in the Box? For VT580 and VT480 onlyIntroduction Features youll enjoyIntroduction to the Projector Congratulations on Your Purchase of the ProjectorPart Names of the Projector Front/TopRear Introduction Bottom Attaching the supplied carrying handleTop Features Introduction Terminal Panel Features VT58/VT57/VT48Part Names of the Remote Control PowerIntroduction Battery Installation Operating Range for Wireless Remote ControlSetting Up the Screen and the Projector Selecting a Location VT580/VT480/VT58/VT57Installation and Connections Selecting a Location VT48 240VT580/VT480/VT58/VT57 Installation and Connections Throw Distance and Screen SizeDistance Chart VT48Installation and Connections Reflecting the ImageConnecting Your PC or Macintosh Computer Making ConnectionsEnabling the computer’s external display Installation and Connections To connect Scart output RGB Installation and Connections Connecting an External Monitor Daisy chain connection is not possibleAudio cable not supplied Video cable not supplied Lamp Projecting an Image Basic Operation Turning on the ProjectorProjecting an Image Basic Operation Press the Enter button to execute the selectionDetecting the Signal Automatically Using the Remote ControlSelecting a Source Adjusting the Picture Size and Position Adjust the Tilt FootLift the front edge of the projector Projecting an Image Basic Operation Zoom FocusCorrecting Keystone Distortion Adjusting with buttons on the cabinetAdjusting with the Remote Control Correcting Keystone DistortionPress the Select or button to select On Turning Up or Down Volume Adjusting the Image Using Auto AdjustOptimizing RGB Picture Automatically Turning off the Projector To turn off the projectorAfter Use Turning off the Image and Sound Freezing a PictureEnlarging a Picture To enable the Security function Changing Lamp ModeConvenient Features Preventing the Unauthorized Use of the ProjectorSelect Yes and press the Enter button To disable the Security function Type in your keyword and press the Enter buttonWhen operating a computer via the remote mouse receiver Using Remote Mouse Receiver VT580/VT480 onlyConnecting the remote mouse receiver to your computer When connecting using the USB terminalAbout Drag Mode SelectUsing On-Screen Menu Using the MenusFor Selecting items Solid triangle Using On-Screen MenuFor Adjusting items Slide bar For Selecting items Radio buttonIndicates the Control Panel Lock is enabled Menu ElementsList of Menu Items PictureReset Selecting Gamma Correction Mode Gamma Correction PresetDetail Settings Selecting Reference Setting Reference Adjusting Color Temperature Color TemperatureReset Using On-Screen Menu Adjusting White Balance White BalanceAdjusting Brightness, Contrast, Sharpness, Color and Hue Menu Descriptions & Functions Image OptionsSelecting Noise Reduction Level Noise Reduction CopyrightMenu Descriptions & Functions Setup Selecting Communication Speed Communication Speed Disabling the Cabinet Buttons Control Panel LockSelecting Menu Color Menu Color Select Setting Auto Adjust Auto AdjustEnabling Power Management Power Management Selecting Menu Display Time Menu Display TimeEnabling Key Sound and Error Sound Beep Using On-Screen Menu Enabling Fan Speed Mode Fan ModeSelecting Signal Format Signal Select Enabling the deinterlace DeinterlaceMenu Descriptions & Functions Information Usage TimeSource Returning to Factory Default Reset Menu Descriptions & Functions ResetUsing On-Screen Menu Version Clearing Lamp Hour Meter Clear Lamp HoursCleaning or Replacing the Filters To clean the air-filterTo replace the filter sponge Cleaning the Cabinet and the Lens MaintenanceReinstall the new filter cover Clear the filter hours used Replacing the Lamp To replace the lampRemove the lamp housing Install a new lamp housingReattach the lamp cover Maintenance Troubleshooting Indicator Messages Power IndicatorProblem Check These Items AppendixPage Specifications OpticalElectrical Mechanical VT580/VT480 3.1 1.3AVT58/VT57/VT48 2.4 1.0A VT580/VT480/VT58/VT48Cabinet Dimensions 120.8Pin Assignments of D-Sub Computer Input Connector Mini D-Sub 15 Pin ConnectorCompatible Input Signal List PC Control Codes VT58/VT57/VT48 PC Control Codes and Cable ConnectionPC Control Codes VT580/VT480 Cable ConnectionAppendix PC Control Connector DIN-8P Troubleshooting Check List PowerComputer TravelCare a service for international travelers TravelCare GuideAsia and Middle East Application Sheet for TravelCare Service Program Condition of your TravelCare Service Program