Kyocera FS-1300D, FS-1100 manual Connections, Connecting the USB Cable, Connecting the Power Cord

Page 48

Connections

This section explains how to start up the printer.

Connecting the USB Cable

Follow the steps as below for connecting the USB cable.

1Connect the USB cable (not included) to the USB Interface Connector.

Note Use a USB cable with a rectangular Type A plug and a square Type B plug. The USB cable should be shielded and no longer than 5 meters (16 feet) long.

2Connect the other end of the USB cable to the computer's USB interface connector.

Connecting the Power Cord

Install the printer close to an AC wall outlet. If an extension cord is used, the total length of the power cord plus extension should be 5 meters (16 feet) or less.

Note Ensure the printer's power switch is off. Only use the power cord supplied with the printer.

1Connect the power cord to the Power Cord Connector at the rear of the printer.

2Connect the other end of the power cord to a power outlet.

3Press the Power Switch to On ( ). The printer begins to warm up.

IMPORTANT If you install the toner container and switch on the power, after a moment the indicators light in anticlockwise direction. When the printer is first switched on after toner installation, there will be a delay of approximately 15 minutes before the printer gets ready to print. Once the [Ready] indicator lights, printer installation is complete.

3-2	Connecting and Printing

Image 48

Contents Operation Guide FS-1100 FS-1300DInstallation Guide Included GuidesOperation Guide This Guide Contents Page Legal and Safety Information About the Operation Guide Conventions in This Guide XxiLegal Information Regarding TradenamesUSB Limited Warranty License AgreementsIBM Program License Agreement LicenseTypeface Trademark Acknowledgement Monotype Imaging License AgreementGeneral Viii Compliance and Conformity FCC Statement for users in the United States and CanadaSafety Information Laser SafetyLaser Notice Radio Frequency TransmitterCdrh Regulations Ozone ConcentrationDeclaration of Conformity for U.S.A CE Marking DirectiveDeclaration of Conformity Australia Canadian Department of Communications Compliance StatementEN ISO DisclaimerEnergy Saving Function Duplex Printing For FS-1300D onlySymbols Installation Precautions Other PrecautionsEnvironment Power Supply/Grounding the Machine Other precautionsHandling of plastic bags Precautions for Use Introduction-xix About the Operation Guide Conventions in This Guide Introduction-xxii Machine Parts Components at the Front of the Printer Components at the Rear of the Printer Cancel Key GO Key Operation PanelIndicators Indicator Status MeaningKeys Key Status Operation FunctionLoading Paper Paper Specifications General GuidelinesPaper Availability Minimum and Maximum Paper Sizes Selecting the Right Paper ConditionComposition Paper SizesBasis weight Paper Weight Equivalence TableMoisture Content Bond Weight lb Europe Metric Weight g/m²Paper Grain Other Paper PropertiesSpecial Paper TransparencyLabels Specification PostcardsEnvelopes Thick Paper Colored PaperPreprinted Paper Recycled paperPaper Weight Paper TypePaper source Paper Type MP trayPreparing the Paper Loading Paper into CassetteLoading Paper Loading Paper Loading Paper into MP Multi-PurposeTray Paper in the opposite direction to counteract the curl Loading Paper Connecting and Printing Connecting the USB Cable Connecting the Power CordConnections Installing the Printer Driver Installing the Printer Driver on Windows PCExpress Mode Custom Mode Installing the Printer Driver on Mac OS To start printing, click OK Manual Duplex For FS-1100 only Long Edge Binding Accessing the Status Monitor Status MonitorExiting the Status Monitor Screen OverviewStatus Monitor icon Status Monitor Settings Appearance Tab Enlarge windowAlways on top Page Status Tab Input TabMedia Tab Printer Tab Connection TabData Tab Others Tab DescriptionUninstalling Software Click UninstallMaintenance Toner Container Replacement Frequency of toner container replacementGeneral Information Starter Toner ContainerReplacing the Toner Container Maintenance Page Cleaning the Printer Page Page Prolonged Non-Use and Moving of the Printer Prolonged Non-useMoving the Printer Maintenance Troubleshooting Indicator combinations,Symptom Check Items Corrective Actions TipsPrint Quality Problems Full single-color printoutDropouts, stray dots Vertical streaksPrinted Results Corrective Action Faint or blurred printing Gray backgroundDirt on the top edge or back PaperUnderstanding Indicators IndicatorNormal Indication Indicator Meaning Maintenance Indication Meaning RemedyError Indication Cleaning Paper Jams Possible Paper Jam LocationsPaper jam location Description Reference General Considerations for Clearing Jams MP TrayPaper Cassette/Paper Feeder Duplexer Inside the Printer Page Rear Cover Troubleshooting Option General Information Expansion Memory Modules Installing the Memory Module Removing a Memory Module Verifying the expanded memoryPaper Feeder PF-100 Network Interface Card IB-23 CompactFlash CF Card Page Option Appendix Specifications Description FS-1100 FS-1300DPDL Prescribe Environmental Standard Requirements Index DimmIndex-2 Index-3 Index-4 Page Page 2007 Is a trademark of Kyocera Corporation

Related manuals

Manual 109 pages 40.4 Kb

Manual 223 pages 29.47 Kb

Manual 109 pages 17.38 Kb