NEC PA231W, PA301W user manual English-19

	B-SHARPNESS*1		Adjusts the sharpness of the blue component of the image.
	(Analog input only)		Press “LEFT” or “RIGHT” to adjust.
	DVI Long Cable		Compensates for image degradation caused by using a long DVI cable.
	(DVI input only)		There are 4 possible settings, with “0” being the lowest level of compensation and “3”
			being the highest level. The default setting is “1”.
Tag4*1	AUTO ADJUST*2		Automatically adjusts the Image Position and H.Size settings and Fine settings.
(Analog			Press “SELECT” to activate Auto Adjustment. Please use test pattern, which is included
input only)			in the enclosed CD-ROM.
	SIGNAL ADJUST		Determines when the auto adjustment is activated automatically.
			The choices are “SIMPLE” and “FULL”. Press “LEFT” or “RIGHT” to select.
				H-size, Fine, H/V Position			Contrast
			SIMPLE		O			X
			FULL		O			O
			O: Automatic Adjustment		X: No Automatic Adjustment
			NOTE: Automatic Adjustment does not work at resolutions less than 800x600 resolution.
	AUTO ADJUST		Determines the automatic adjustment level for Auto Adjust. The choices are “SIMPLE”,
	LEVEL		“FULL” and “DETAIL”. Press “LEFT” or “RIGHT” to select. Refer to the below table.
				Size, Fine, Position		Contrast			Black Level		Time
			SIMPLE	O		X				X	1 second
			FULL	O		O				X	1.5 seconds
			DETAIL*	O		O				O	5 seconds
			O: Automatic Adjustment		X: No Automatic Adjustment
			* “DETAIL” activates automatic long cable (skew, peaking) adjustment.
	A-NTAA SW		The Advanced No Touch Auto Adjust function is able to recognize new signals even
			when neither the resolution nor the refresh rate has changed. If several PCs are
			connected to the monitor, and each transmit very similar (or even the same) signals in
			terms of resolution and refresh rates, the monitor recognizes that there is a new signal
			and automatically optimizes the picture without the need for any action on the part of the
			user.
			OFF: A-NTAA is disabled.
			ON: If a change in signal is detected A-NTAA will adjust the monitor to the optimal
			settings for the new signal. If no change in the signal is detected then A-NTAA does not
			activate. The screen will be blank while the monitor optimizes the signal.
			OPTION: Functions the same as ON, except that the screen does not go blank when the
			monitor makes adjustments for changes in signal, allowing the monitor to display the new
			signal faster. When using an external switching device to connect 2 or more PCs to the
			monitor, using the ON or OPTION settings is suitable.
	AUTO CONTRAST*2		Adjusts the image displayed for non-standard video inputs. Press “SELECT” to adjust.
			Any adjustment requires the image to have white portions.
	CONTRAST		Adjusts the image brightness and contrast in relation to the background.
			Press “LEFT” or “RIGHT” to adjust.
	AUTO BLACK LEVEL*2		Automatically adjusts the black level. Any adjustment requires the image to have black
			portions. Press “SELECT” to activate Auto Adjust.
	BLACK LEVEL		Adjusts the RGB black level by input signal level.
Tag5	H.POSITION	Controls Horizontal Image Position within the display area of the LCD.
			Press “LEFT” or “RIGHT” to adjust.
	V.POSITION		Controls Vertical Image Position within the display area of the LCD.
			Press “LEFT” or “RIGHT” to adjust.
	H.SIZE*1		Adjusts the horizontal size of the screen.
	(Analog input only)		If the “AUTO Adjust function” do not give you a satisfactory picture setting, a further
			tuning can be performed using the “H.Size (V.Size)” function (dot clock). For this a Moiré
			test pattern could be used. This function may alter the width of the picture. Use LEFT/
			RIGHT Menu to center the image on the screen. If the H.Size (V.Size) is incorrectly
			calibrated, vertical bands will appear. The image should be homogeneous.
	FINE*1		Improve focus, clarity and image stability by increasing or decreasing this setting.
	(Analog input only)		If the “Auto Adjust function” and the “H.Size” function do not give you a satisfactory
			picture setting, a fi ne tuning can be performed using the “Fine” function. For this a Moiré
			test pattern could be used. If the Fine value is incorrectly calibrated, horizontal lines will
			appear on the display. The image should be homogeneous.
*1 Only for PA231W/PA241W.									*2 This item does not reset by FACTORY PRESET (Tag7).

English

English-19