MB260
Analysis origin setup |
| Paper tray selection |
If you want, you can change the origin of the scanner.
By entering new values for X and Y in mm (X < 209 and Y < 280), you move the analysed area as shown on the diagram below.
843 - ADVANCED FCT/COPY/ORIGIN
1 Press , enter 843 using the keypad.
2Select the X and Y coordinates with the buttons or .
3Setup the desired coordinates with the numerical
keypad or the buttons and .
4Confirm your choice by pressing the OK button.
5Quit this menu by pressing the 
button.
Contrast setup
The CONTRAST parameter allows to choose the photocopy contrast.
The Automatic selection can have two meanings depending on the paper format defined on the paper trays. The following table describes the different cases.
|
| Default tray | Tray used for copy | |||
|
|
|
|
| ||
|
|
|
|
| ||
|
|
| Selection between | the | ||
Same paper |
| AUTOMATIC | main | tray | and | the |
|
| manual tray. |
|
| ||
format in the |
|
|
|
| ||
|
|
|
|
|
| |
trays |
|
|
|
|
|
|
| MANUAL | The | manual | tray | is | |
|
| |||||
|
| used. |
|
|
| |
|
|
|
|
|
| |
|
|
|
| |||
Different |
| AUTOMATIC | The main tray is used. | |||
paper format |
|
|
|
|
|
|
| MANUAL | The | manual | tray | is | |
in the trays |
| |||||
| used. |
|
|
| ||
|
|
|
|
|
| |
|
|
| ||||
852 - ADVANCED FCT/SCAN. & PRINT/TRAY | ||||||
|
|
|
|
| PAPER | |
1 Press | , enter 852 using the keypad. |
|
| |||
2Select the default paper tray to use, AUTOMATIC
or MANUAL, with the buttons and .
3Confirm by pressing the OK button.
4Quit this menu by pressing the 
button.
Flat-bed analysis margins setup
844 - ADVANCED FCT/COPY/CONTRAST
1 Press , enter 844 using the keypad.
2Setup the desired level of contrast with the buttons and .
3Confirm your choice by pressing the OK button.
4Quit this menu by pressing the 
button.
If you want to, you can offset the lateral margins of the document to the left or right during the analysis with your
854 - ADVANCED FCT/SCAN. & PRINT/ FLATBED MARG
1 Press , enter 854 using the keypad.
2Setup the left / right margins offsets (by 0.5 mm
steps) with the buttons and .
Brightness setup |
| 3 | Confirm by pressing the OK button. |
| ||||
The BRIGHTNESS parameter allows to lighten or darken | 4 | Quit this menu by pressing the | button. | |||||
your output. |
|
|
|
|
|
| ||
| 845 - ADVANCED FCT/COPY/BRIGHTNESS |
| Left and right printing margins setup | |||||
1 | Press | , enter 845 using the keypad. |
| If you want to, you can offset the lateral margins of the | ||||
2 | Setup the desired brightness with the buttons |
| document to the left or right during printing. | |||||
| and . |
|
|
|
| 855 - ADVANCED FCT/SCAN. & PRINT/ | ||
3 | Confirm your choice by pressing the OK button. |
|
| |||||
|
| PRINTER MARG | ||||||
4 | Quit this menu by pressing the | button. |
|
| ||||
1 | Press , enter 855 using the keypad. | |||||||
|
|
|
| |||||
Paper type setup |
| 2 | Setup the left / right margins offsets (by 0.5 mm | |||||
|
|
| steps) with the buttons and . |
| ||||
| 851 - ADVANCED FCT/SCAN. & PRINT/PAPER | 3 | Confirm by pressing the OK button. |
| ||||
|
|
| TYPE | 4 | Quit this menu by pressing the | button. | ||
1 | Press | , enter 851 using the keypad. |
|
|
|
| ||
2Select the paper NORMAL or THICK that you use
with the buttons and .
3Confirm your choice by pressing the OK button.
4Quit this menu by pressing the 
button.
- 20 -