Emerson 7000, 4000 appendix Closed-Transition Automatic Transfer Switches

Page 24

4--4 Description of Operation

Closed–Transition Automatic Transfer Switches continued

TEST MODE

TEST CIRCUIT 5 Waiting for Emerg Acceptable

TEST MODE

TEST CIRCUIT 5

Load on Emerg

Closed–Transition Load Transfer to Emergency Source due to Transfer Test

The sequence for closed–transition load transfer to the emergency source begins automatically when the controller detects a transfer test signal.

Transfer Test Signal. Test transfer signal can be from the Transfer Control switch (Feature 5), the engine–generator exerciser clock (Feature 11C), or via the serial port (Feature 72A). When using the Transfer Control switch, it must be held in the Transfer Test position until the emergency source becomes available (within 15 seconds).

The controller begins the load transfer sequence by de–energizing the SE, SE2, and NR relays. Feature 1C engine starting time delay is bypassed during transfer test.

Engine Start Signal. When the NR relay de–energizes it signals the engine–generator to start. The controller monitors the emergency source, waiting for it to become acceptable. Both voltage and frequency must reach preset pickup points before the emergency source is accepted. Usually about 10 seconds elapse from dropout of the NR relay to acceptance of the emergency source. This interval occurs because the engine–generator must crank, start, and run up to nominal pickup points. If the emergency source is available immediately, the controller will accept it as soon as the NR relay drops out.

When the emergency source becomes acceptable, the controller starts the Feature 2B time delay on transfer to emergency (if desired). If the emergency source fails while Feature 2B time delay is running, the controller again waits for the emergency source to become acceptable again and restarts Feature 2B.

At the conclusion of the Feature 2B time delay, the controller starts the synchronization time delay which allows both sources to stabilize. After the synchronization time delay, the controller starts the in–sync monitor. Three criteria must be met for the sources to be considered in–sync. The phase difference between the sources must be less than 5 degrees, the frequency difference must be less than 0.2 Hz, and the voltage difference must be less than 5%. These parameters are displayed. The controller waits for the sources to become in–sync. At the same time, the failure to sync time delay is running. If the failure to sync time exceeds the user selected time, the failure to sync output is activated and remains active until it is reset via the alarm reset. The controller continues the transfer sequence even after the failure to synchronize alarm becomes active.

When the sources become in–sync the controller is ready to transfer the load to emergency.

Load Transfer. To transfer the load to the emergency source the controller energizes the ER2 relay. The transfer switch CE coil energizes, and all CE transfer switch contacts (mains, controls, auxiliaries) reverse position. The load is connected to both the Normal and Emergency sources. The extended parallel time delay is started and the controller energizes the ER relay. The transfer switch CN coil energizes, and all CN transfer switch contacts (mains, control, auxiliaries) reverse position to disconnect the Normal source. The load is now only connected to the Emergency source. If the sources are paralleled longer than the extended parallel time setting the controller activates an extended parallel output. It also deenergizes the ER and ER2 relays, energizes the SE and SE2 relays, and it locks out any further transfer operations. This lock–out condition is reset via the alarm reset.

Image 24
Contents Description 381333-126 KPower Control Center display and keypad Left-Right Arrows Enter/Save SettingsControl Overview Up-Down ArrowsSettings Overview How to Change a Setting TipVoltage & Frequency Settings NormalvoltageunbalNormal Frequency Emerg FrequencyCP Settings Normal VoltageNormal Frequency Normal Voltage UnbalanceTime Delay Settings Standard Time Delays TD NE Xfer SignalTD EN Xfer Signal Bypass Currently Running TDFeatures Settings Phase Rotation Monitor In-Phase MonitorCommit to Xfer After TD Normal Fail see Shed LoadGeneral Settings Primary Failure Detection not shownDefault to Factory Settings Reset Engine Exerc ProgramsChange Password Menu Language not shownEngine Exerciser Settings JANPresent DATE/TIME P1 Engine ExerciserEngine Exerciser Settings Menus Present Date/TimeP1-7 Engine Exercisers View Event Log Logged EventsEvent Types Event ReasonsService Statistics / Diagnostics View Service DataATS Statistics Source StatisticsService Factory Selectable Features Status Information Source AcceptabilityATS Status Normal Source StatusDisplay Messages and their Meaning Test Mode Serial Comm Test Mode Test CircuitWrong Password XTD Parallel AlarmOpen-Transition 2-position Automatic Transfer 4ATS,7ATS,7ATB Load Transfer To EmergencyOpen-Transition 2-position Automatic Transfer Switches Load Retransfer To NormalClosed-Transition Automatic Transfer 4ACTS, 7ACTS, 7ACTB Closed-Transition Automatic Transfer Switches Closed-Transition Load Retransfer To Normal Bypass Closed-Transition Load TransferDelayed-Transition Automatic Transfer 4ADTS, 7ADTS, 7ADTB Delayed-Transition Automatic Transfer Switches Controller Cover Removal Figure A-1. Cover release latchesDIP Switch Actuators Transfer Switch TypeNominal Source Voltage Selection Phases of Normal & Emergency Sources Lost or Forgotten PasswordFrequency of Sources Data Input LockVoltage Jumper Blocks Figure A-3. Location of jumper blocksIndex
Related manuals
Manual 172 pages 36.16 Kb Manual 12 pages 23.06 Kb Manual 28 pages 10.34 Kb Manual 9 pages 27.84 Kb

4000, 7000 specifications

The Emerson 7000 series is a versatile and advanced automation solution designed for modern industrial environments. Renowned for its reliability, scalability, and performance, the Emerson 7000 series is tailored to meet the complex demands of various industries, including oil and gas, chemical manufacturing, power generation, and food and beverage.

At the heart of the Emerson 7000 series is its powerful and flexible architecture. This series integrates seamlessly with existing systems, allowing for easy upgrades without disrupting ongoing processes. The modular design enables users to customize their setups according to their specific needs, providing unmatched adaptability in dynamic operations.

One of the standout features of the Emerson 7000 is its intelligent diagnostics capabilities. This technology leverages advanced algorithms and machine learning to predict equipment failures and maintenance needs, thus minimizing unplanned downtime. By continuously monitoring critical parameters, the system provides operators with actionable insights, enhancing operational efficiency and safety.

The Emerson 7000 series also focuses on user-friendly interfaces. Its intuitive design allows operators to quickly navigate complex data and analytics, facilitating quicker decision-making. The human-machine interface (HMI) provides a clear visual representation of processes, empowering users to manage operations effectively.

Another cutting-edge technology in the Emerson 7000 series is its cybersecurity measures. With the increasing threat of cyber-attacks in industrial environments, Emerson has prioritized the integration of robust security protocols. These features protect sensitive data and ensure the integrity of operations, safeguarding organizations from potential breaches.

Additionally, the Emerson 7000 series supports a wide range of communication protocols, making it compatible with various devices and systems. This interoperability allows for greater collaboration between different technologies within a facility, streamlining workflows and enhancing productivity.

Lastly, the Emerson 7000 emphasizes sustainability and energy efficiency. By providing insights into energy consumption and operational performance, the system helps organizations minimize their environmental impact and reduce operational costs.

In summary, the Emerson 7000 series stands out as a comprehensive automation solution that combines cutting-edge technologies, user-friendly interfaces, robust cybersecurity, and a commitment to sustainability. With its ability to adapt to diverse industrial needs and enhance operational efficiency, the Emerson 7000 continues to be a preferred choice for businesses seeking to navigate the complexities of modern manufacturing and process automation.