Emerson MVME55006E VMEbus Connectors P1 & P2 PMC Mode, VME Connector P2 Pin Assignments PMC Mode

Page 82

Connector Pin Assignments	VMEbus Connectors (P1 & P2) (PMC Mode)

5.2.10VMEbus Connectors (P1 & P2) (PMC Mode)

The VME P1 and P2 connectors are 160-pin DINs. The P1 connector provides power and VME signals for 24-bit address and 16-bit data. The pin assignments for the P1 connector are specified by the VME64 Extension Standard (refer to Appendix C, Related Documentation, for the link to this specification).

Row B of the P2 connector provides power to the MVME5500 and to the upper eight VMEbus address lines, and additional 16 VMEbus data lines. Please read the notes below as they pertain to the P2 connector.

1.When J28 is configured for IPMC mode, –12V is supplied to P2 pin A30. If there is an incompatible board plugged into this P2 slot, damage may occur.

2.When J32 is configured for IPMC mode, +12V is supplied to P2 pin C7. If there is an incompatible board plugged into this P2 slot, damage may occur.

3.J102 – J110 should be configured for PMC 2 I/O to connect PMC slot 2 user I/O from J24 to the P2 connector.

The pin assignments for the P2 connector are as follows:

Table 5-16 VME Connector (P2) Pin Assignments (PMC Mode)

Pin	ROW Z	ROW A	ROW B	ROW C	ROW D

1	PMC2_2 (J24-2)	PMC1_2 (J14-2)	+5V	PMC1_1 (J14-1)	PMC2_1 (J24-1)
				/P2_RX-

2	GND	PMC1_4 (J14-4)	GND	PMC1_3 (J14-3)	PMC2_3 (J24-3)
				/P2_RX+

3	PMC2_5 (J24-5)	PMC1_6 (J14-6)	RETRY#	PMC1_5 (J14-5)	PMC2_4 (J24-4)
			(No	/P2_TX-
			connect)

4	GND	PMC1_8 (J14-8)	VA24	PMC1_7 (J14-7)	PMC2_6 (J24-6)
				/P2_TX+

5	PMC2_8 (J24-8)	PMC1_10 (J14-10)	VA25	PMC1_9 (J14-9)	PMC2_7 (J24-7)

6	GND	PMC1_12 (J14-12)	VA26	PMC1_11 (J14-11)	PMC2_9 (J24-9)

7	PMC2_11	PMC1_14 (J14-14)	VA27	PMC1_13 (J14-13)	PMC2_10 (J24-10)
	(J24-11)

8	GND	PMC1_16 (J14-16)	VA28	PMC1_15 (J14-15)	PMC2_12 (J24-12)

9	PMC2_14	PMC1_18 (J14-18)	VA29	PMC1_17 (J14-17)	PMC2_13 (J24-13)
	(J24-14)

10	GND	PMC1_20 (J14-20)	VA30	PMC1_19 (J14-19)	PMC2_15 (J24-15)

11	PMC2_17	PMC1_22 (J14-22)	VA31	PMC1_21 (J14-21)	PMC2_16 (J24-16)
	J24-17)

12	GND	PMC1_24 (J14-24)	GND	PMC1_23 (J14-23)	PMC2_18 (J24-18)

13	PMC2_20	PMC1_26 (J14-26)	+5V	PMC1_25 (J14-25)	PMC2_19 (J24-19)
	(J24-20)

14	GND	PMC1_28 (J14-28)	VD16	PMC1_27 (J14-27)	PMC2_21 (J24-21)


82		MVME55006E Single-Board Computer Installation and Use (6806800A37D)

Image 82

Contents MVME55006E Single-Board Computer Contact Address Contents Contents RAM55006E Memory Expansion ModuleSpecifications Related Documentation List of Tables List of Tables 14 VIO Keying Pin Settings List of FiguresList of Figures Overview of Contents About this ManualNotation Description ConventionsAbout this Manual Model Number Description BoldAbout this Manual Notation Description Summary of ChangesComments and Suggestions Date Change ReplacesAbout this Manual Introduction Hardware Preparation and InstallationOverview Getting StartedUnpacking Guidelines Overview of Startup ProceduresHardware Preparation and Installation Startup OverviewConfiguring the Hardware Configuring the HardwareMVME5500 Jumper Settings Configuring the BoardJumpers Switches Function Settings Items in brackets are factory default settings Configuring the BoardHardware Preparation and InstallationEthernet 2.2 PMC/SBC Mode Selection Front Panel and Rear P2 Ethernet Settings J102 J110 SettingsFlash 0 Programming Enable Switch S3-1 Flash Boot Bank Select Header J8Flash Boot Bank Select Header J8 Flash 0 Block Write Protect Switch S3-2 Safe Start ENV Switch S5-1S5-1 Settings PCI Bus 0.0 Speed Switch S4-1 Srom Initialization Enable Switch S5-2Srom Initialization Enable Switch S5-2 S4-2 Settings PCI Bus 1.0 Speed Switch S4-2J27 Settings VME Scon Select Header J27S3-3 Settings Eeprom Write Protect Switch S3-3Setting the PMC Vio Keying Pin Eeprom Write Protect Switch S3-3Installing the RAM5500 Module ProcedureInstalling PMCs Installing PMCsMounting the PMC Module 15 Typical Placement of a PMC Module on a VME Module Primary PMCspan16 PMCspan Installation on a VME Module Primary PMCspanSecondary PMCspan Installing the Board Installing the BoardConnector Function MVME5500 ConnectorsConnection to Peripherals Completing the Installation Applying PowerSwitches and Indicators Startup and OperationFront-Panel LED Status Indicators Function Label Color DescriptionBlock Diagram Functional DescriptionFeature Description FeaturesMVME5500 Features Summary Functional DescriptionSystem Controller ProcessorL3 Cache ProcessorFunctional DescriptionInterrupt Controller CPU Bus InterfaceMemory Controller Interface 4 I2C Serial Interface and DevicesDirect Memory Access DMA Direct Memory Access DMATimers Flash MemoryGigabit Ethernet Interface System MemoryPCI Local Buses and Devices 2 10/100Mb Ethernet InterfacePCI Idsel Definition PCI-to-PCI BridgesPMC Sites PCI Bus ArbitrationAsynchronous Serial Ports Real Time Clock and NvramVME Interface Sources of ResetSystem Control and Status Registers PMC ExpansionDebug Support Functional Description RAM5500 Feature SummaryRAM55006E Memory Expansion Module 1 RAM5500 DescriptionClocks Memory Expansion Connector Pin AssignmentsSrom RAM55006E Memory Expansion ModuleMemory Expansion Connector Pin Assignments RAM5500 Connector P1 Pin AssignmentsPin Signal CKD00 CKD01 CKD02 CKD03 CKD04 CKD05 RAM5500 Programming IssuesRAM55006E Memory Expansion Module RAM5500 Programming IssuesSerial Presence Detect SPD Data Serial Presence Detect SPD Data MOTLoad Firmware MOTLoad CommandsImplementation and Memory Requirements Tests UtilitiesMOTLoad Firmware Command List Command ListMOTLoad Commands Command DescriptionMOTLoad FirmwareCommand List Command ListMOTLoad Firmware MOTLoad Commands Using the Command Line Interface Using the Command Line InterfaceMOTLoad FirmwareRules HelpDefault VME Settings Firmware SettingsFirmware SettingsMOTLoad Firmware PCI Slave Image 4 Default VME Settings VMEbus Slave Image 0 Translation Offset =1.1 CR/CSR Settings Deleting VME Settings Remote Start Connector Pin Assignments ConnectorsCOM1 Connector J1 Pin Assignments Asynchronous Serial Port Connector J1Ethernet Connectors J2 Ethernet Connector J2 Pin AssignmentsIpmc Connector J3 Pin Assignments Ipmc Connector J3Ipmc Connector J3 4 PCI/PMC Expansion Connector J4 PCI/PMC Expansion Connector J4 Pin AssignmentsPCI/PMC Expansion Connector J4Connector Pin Assignments AD1 AD0 AD3 AD2 AD5 AD4 AD7 AD6 AD9 AD8CPU COP Connector J5 Pin Assignments CPU COP Connector J5Connector Pin AssignmentsCPU COP Connector J5 PMC 1 Connector J11 Pin Assignments PMC 1 Interface Connectors J11, J12, J13, J14PMC 1 Interface Connectors J11, J12, J13, J14 PMC 1 Connector J12 Pin Assignments PMC 1 Connector J13 Pin Assignments PMC 1 Connector J14 Pin Assignments 10 Boundary Scan Connector J18 Pin Assignments Boundary Scan Connector J18PMC 2 Interface Connectors J21, J22, J23, J24 11 PMC 2 Connector J21 Pin Assignments12 PMC 2 Connector J22 Pin Assignments 13 PMC 2 Connector J23 Pin Assignments 14 PMC 2 Connector J24 Pin Assignments Asynchronous Serial Port COM2 Planar Connector J33 15 COM2 Planar Connector J33 Pin Assignments16 VME Connector P2 Pin Assignments PMC Mode VMEbus Connectors P1 & P2 PMC ModePin VMEbus Connectors P1 & P2 SBC Mode VMEbus Connectors P1 & P2 SBC ModeConnector Pin Assignments17 VME Connector P2 Pinout with IPMC712 Pin Row Z Row a Row B Row C Row D18 VME Connector P2 Pinouts with IPMC761 VMEbus Connectors P1 & P2 SBC ModeMemory Expansion Connector P4 19 Memory Expansion Connector P4 Pin AssignmentsMemory Expansion Connector P4Connector Pin Assignments Connector Pin AssignmentsHeaders HeadersJ100 J101 Pin Signal J34 J97J98 J99 22 PMC/SBC Mode Selection Headers J28, J32 Pin Assignments J28 J32 Pin Signal23 P2 I/O Selection Headers J102 J110 Pin Assignments SBC/IPMC712 Mode SBC/IPMC761 Mode PMC Mode 24 Flash Boot Bank Select Header J8 Pin Assignments 25 VME Scon Select Header J27 Pin AssignmentsConnector Pin Assignments Environmental Specifications SpecificationsPower Requirements Supply Current RequirementsSpecificationsEnvironmental Specifications 207,058 hoursThermally Significant Components Thermal ValidationTable B-1 Thermally Significant Components Thermal ValidationThermally Significant Components 100Component Temperature Measurement Component Temperature MeasurementPreparation Measuring Case Temperature Measuring Junction TemperatureMeasuring Local Air Temperature Thermal ValidationMeasuring Case Temperature Figure B-4 Machining a Heatsink104 Manufacturers’ Documents Emerson Network Power Embedded Computing DocumentsRelated Documentation Table C-2 Manufacturers’ DocumentsRelated DocumentationManufacturers’ Documents 106Related Specifications Related SpecificationsTable C-3 Related Specifications Document Title and Source Or Search TermRelated Documentation 108Index Numerics110