Sound
Before you begin:
You must set Home in Location. ➟ p.31
Otherwise, personalized Picture and Sound settings will not be memorized after the unit goes into Standby mode.
1 Press 
and use ▲▼ to select Sound, then press OK.
Picture | Auto sound | Standard |
Sound | Equalizer |
|
Setup | *SRS TruSurround XT | On |
Features | Auto volume leveling | Off |
Language | TV speakers | On |
USB | Digital output format | Multichannel |
| Audio setting | Stereo |
2 Use ▲▼◄► to select the item you want to adjust, then press OK.
to select the desired setting, then press OK.
(Personal, Standard, Vivid, Sports, Movie, Music and News) Auto sound When you adjust the following settings (Equalizer, SRS
TruSurround XT*, Incredible Surround* and Auto volume leveling), Personal sound will be set automatically.
Adjust the tonal quality for each frequency.
Equalizer | Cursor ◄ |
| Cursor ► |
to adjust each level of tonal | quality |
| |
| Press BACK to go back to the previous menu. | ||
This selects sound modes for more spatial or surround sound reproduction.
*SRS | Off | to set SRS TruSurround XT® to Off |
TruSurround XT | On | to set SRS TruSurround XT® to On |
Incredible Surround gives you the stereophonic virtual space through your existing
*Incredible | Off | Natural effect. |
Surround | On | Emphasized effect. |
*This part differs depending on the product you have.
•SRS TruSurround XT for 40PFL4708, 39PFL2708, 32PFL3508, 32PFL4508, 29PFL4508, 24PFL4508.
•Incredible Surround for 50PFL3708, 46PFL3708, 40PFL1708.
This function keeps a constant loudness differential between the TV commercials and the programs.
Auto volume | Off | to remove the auto volume leveling |
leveling | On | to reduce volume differences between |
|
| the TV commercials and the programs |
You can select the Audio Output from the unit’s speakers or not. If your amplifier is HDMI link function compatible and connected by an HDMI cable to this unit, some sound operations such as volume up can be changed by using this unit’s remote control.
| On | to output sound from the unit’s speakers |
| Off | not to output sound from the unit’s |
| speakers | |
TV speakers |
| |
Speakers | to control Audio Output from your | |
| connected EasyLink Compliant Devices | |
| EasyLink | with VOL + / − by using this unit's |
|
| remote control. |
You can select audio output through a digital audio output connector.
|
| to output multichannel signals. |
Digital output | Multichannel | (When the audio of the content is PCM, |
it will be output in PCM even if | ||
format |
| Multichannel is selected.) |
| PCM | to output PCM signals. |
24 English
You can set the output mode as a default for the sound mode (Analog TV only).
This setting is not interlocked when you change the output mode by pressing SAP. Refer to Switching audio mode. ➟ p.19
| Stereo | to output |
Audio setting | Mono | to output |
| SAP | to output second audio program |
Setup
Before you begin:
Make sure the unit is connected to antenna or cable.
1 Press 
and use ▲▼ to select Setup, then press OK.
Picture
Sound
Setup
Features
Language
USB
2 Adjust the following items.
Autoprogram
Be sure the RF cable is correctly connected to this unit and you are registered with your cable TV provider when you install Cable channels.
1 Use ▲▼ to select Autoprogram, then press OK.
• If you run Autoprogram when you have locked channels, a message appears asking to enter your PIN. Enter your PIN in order to complete the installation. You need to set the channel lock again after the installation.
2 Use ▲▼ to select an appropriate option, then press OK.
–When Antenna is selected, the TV detects any
–When Cable is selected, the TV detects signals supplied by cable. It searches for DTV, Analog TV and Cable channels available in your area.
Picture | Autoprogram will rescan all channels. | Back |
Sound | Auto programming may take more than 20 | Antenna |
Setup | minutes to complete. | Cable |
| ||
Features | Select your signal source. |
|
Language |
| |
Antenna |
| |
USB |
|
|
Cable Or
ANTENNA IN