Philips C221S3 Regulatory Information, Lead-free Product, GS EK1-20002011 GS mark requirement

Page 24

5. Regulatory Infomation

5. Regulatory Information

Lead-free Product

Lead free display promotes environmentally sound recovery and disposal of waste from electrical and electronic equipment.Toxic

substances like Lead has been eliminated and compliance with European community’s stringent RoHs directive mandating restrictions on hazardous substances in electrical and electronic equipment have been adhered to in order to make Philips monitors safe to use throughout its life cycle.

CE Declaration of Conformity

This product is in conformity with the following standards

EN60950-1:2006+A11:2009+A1:20 10+A12:2011 (Safety requirement of Information Technology Equipment)

EN55022:2010 (Radio Disturbance requirement of Information Technology Equipment)

EN55024:2010 (Immunity requirement of Information Technology Equipment)

EN61000-3-2:2006 +A1:2009+A2:2009 (Limits for Harmonic Current Emission)

EN61000-3-3:2008 (Limitation of Voltage Fluctuation and Flicker) following provisions of directives applicable.

EN60601-1-2:2002 (Medical electrical equipment. General requirements for safety Collateral standard, Electromagnetic compatibility Requirements and tests)

2006/95/EC (Low Voltage Directive)

2004/108/EC (EMC Directive)

2009/125/EC (ErP Directive, EC No. 1275/2008 Implementing Directive for Standby and Off mode power consumption)

93/42/EEC, 2007/47/EC (Medical Device Directive)

2011/65/EU (RoHS Directive)

and is produced by a manufacturing organization on ISO9000 level.

ISO9241-307:2008 (Ergonomic requirement, Analysis and compliance test methods for electronic visual displays)

GS EK1-2000:2011 (GS mark requirement)

prEN50279:1998 (Low Frequency Electric and Magnetic fields for Visual Display)

MPR-II (MPR:1990:8/1990:10 Low Frequency Electric and Magnetic fields)

TUV IEC60601-1 (EN 60601-1:2006 Medical electrical equipment - Part 1: General requirements for basic safety and essential performance)

EN 60601-1-2:2007 Medical electrical equipment - Part 1-2: General requirements for basic safety and essential performance - Collateral standard: Electromagnetic compatibility - Requirements and tests

Federal Communications Commission (FCC) Notice (U.S. Only)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

22

Image 24
Contents Troubleshooting & FAQs Table of Contents Safety Information Disconnecting DeviceSytems CisprShould be at least 30% Immunity test KHz to 80 MHz Safety precautions and maintenance OperationNotational Descriptions Important information for Burn-in/Ghost imageDisposal of product and packing material Waste Electrical and Electronic EquipmentWeee Taking back/Recycling Information for CustomersAntiMicrobial Do you ever wonder how many germs thrive on your equipment?Setting up the monitor InstallationPackage contents Monitor is ready to be used as second monitor Remove Base Stand and Base Remove the Base Stand100mm DisplayLink Graphics Software Installation Installation procedureClick I Accept, then software start to install Operating the monitorHow to control the display Click Advanced Configuration WDP opensMenu Option Sub-menu Option Description Extend these displaysDisplay marked 2 becomes blank Display marked 1 becomes blankMenu Description Menu Option Off Switches off the secondary display Optimize for Video When playing back video contentConfigure this feature The resolution of screen Off DisplayLink display primary MirrorTechnical Specifications TFT-LCDLED Resolution & Preset Modes MtbfRohs YES Regulatory Information Lead-free ProductGS EK1-20002011 GS mark requirement Federal Communications Commission FCC Notice U.S. OnlyCommission Federale de la Communication FCC Declaration Varning Paikka/IlmankiertoVaroitus Plassering/VentilasjonErgonomie Hinweis nur Deutschland Auf der Rückwand des Gerätes befindet sichNur original-Ersatzteile verwendet werden Achtung Beim AufstellenChina RoHS 中国电子信息产品污染控制标识要求中国 RoHS法规标示要求产品中有毒有害物质或 元素的名称及含量Customer care and warranty Philips’ Flat Panel Monitors Pixel Defect PolicyPixels and Sub pixels Types of Pixel DefectsBlack Dot Defects Proximity of Pixel DefectsTotal bright dot defects of all types Dark subpixelCustomer Care & Warranty CountryConsumer care number Price IBA FujitsuCPS Contact Information for Apmea region AL Shahd Computer L.L.CTroubleshooting No Picture Power LED not litDisconnect and reconnect the USB cable again Image appears distorted.Text is fuzzy or blurredGeneral FAQs Monitor FAQsCan I use my PC on Linux/ Apple Not at the momentAns Montior Monitor will turn off completelyKoninklijke Philips Electronics N.V. All rights reserved