Black Box LR1530A-R3 Basic Leased Line Configuration, Quick Start PPP Leased Line Connections

Page 32

Applications

Basic Leased Line Configuration

routers shipped outside North America are configured to have a default setting as a leased line router. The router will operate as a PPP leased line bridge/router if the frame relay function is disabled. The Leased Line router establishes PPP (Point to Point Protocol) WAN connections to other PPP Leased Line router units or to other vendors PPP leased line routers via direct leased line connections.

Configuration: The default configuration for North American router is to have frame relay enabled. To run PPP leased line, frame relay must be disabled

7Frame Relay disable Location: Main

ÄConfiguration

ÄWAN Set up

ÄLink Set up

ÄFrame Relay

Ädisabled

The router will request confirmation of the change, enter “yes”.

“Quick Start” PPP Leased Line Connections

The PPP Leased Line router requires only a few configuration parameters to establish a direct connection to another PPP IP router.

Once the connection is established and is working properly, the router should be configured with a remote site profile entry for that vendors router.

Before the router can establish a link connection to another PPP router, the link speed information must be defined. Refer to the following diagram that shows an router unit and another vendors unit connected together with a direct leased line connection.

26

Image 32
Contents Frame Relay/Leased Line Bridge/Router Specifications Normas Oficiales Mexicanas Electrical Safety Statement Page Page Page Contents Introduction to Filtering Appendix D Software Upgrades Page Unpack the unit Select a SiteIdentify the Connectors Rear View of the CSU-DSU routerMake the WAN Link Connection Connect to the ConsoleMake the LAN Connections Installation Power Up the router Login and Enter the Required ConfigurationMandatory Configuration Mandatory ConfigurationLink Interface Type Setting the Link Interface TypeSet Link Interface Type Location Main Setting the T1/E1Parameters Service parameters Location MainT1/E1 Selection Location Main Framed/unframed/SF/ESFAs specifed First channel Number number of channelsSet Link Interface Type Location Main Identify the Status LEDs GreenFront View of the router Typical Applications & HOW to Configure Them Managing the router Using Menus Option Name Configuration Option Name Location MainConventions Basic Frame Relay Configuration Frame Relay configurationLink Speed Frame Relay enable Location MainLink Speed Location Main Auto Learning the Frame Relay Configuration LMI Type Manual Configuration LMI TypeAuto-Learning Location Main IP Address / Subnet mask size Quick Start Frame RelayIP Address PPP Encapsulation Location Main Basic Leased Line Configuration Frame Relay disable Location MainDisabled Quick Start PPP Leased Line ConnectionsBasic PPP Leased Line Configuration Local IP Address Location MainBridge Connection Should You Bridge or Route? Configure as an Ethernet Bridge Bridged Local Area NetworksIP Address Applications Configure as an Ethernet IP router IP Routed Local Area NetworksIP Address Default Gateway Define an IP Default GatewayDefault Gateway Location Main Remote Site Next Hop Cost Add Define an IP Static RouteEdit Static Route Location Main Define an IP Subnet Mask IP Address & Subnet Size Location Main IP Address / mask sizeApplications Configure as an Ethernet IPX router Novell Servers in Both LocationsApplications Novell Servers in One Location Only IPX Routed Local Area Networks Servers on one sideIPX Frame Types Location Main PPP Link Configuration Overview Numbered LinksUnnumbered Links Configure Dynamic Host Configuration Protocol Dhcp Services Location MainServer IP Address Pool Location MainLocal + External DNS Server Configuration DNS Set-Up Location MainConfigure Network Address Translation NAT NAT Enabled Location MainEnabled NAT ExportsTranslation type Location Main Security Level Configure PPP SecuritySecurity Level Location Main Security Database Entry Location Main Incoming PAP Password Incoming Chap SecretOutgoing PAP Password Outgoing Chap Secret Configure Firewall 10 Sample Firewall ApplicationFirewall WAN Remote Site Filter direction Location Main FTP & WWW Designated Servers Location MainFirewall LAN Filter Direction Location Main Firewall Table Entry Location MainFirewall Location Main Applications MAC Address Filtering Introduction to FilteringPattern Filtering Not Introduction to Filtering NetBIOS &NetBEUI Microsoft Windows Popular FiltersBridge IP & Related TrafficNetBIOS over TCP BanyanIP Router Other interesting TCP PortsAppendix a Menu Trees Menu Tree From previous Page Appendix B Octet Locations on Ethernet Frames Octet Locations on Ethernet Frames Ethernet Type Codes ARPOctet Locations on Ethernet Frames Octet Locations on a Bridged XNS Frame Octet Locations on Ethernet Frames Opening the case Appendix C Servicing InformationIdentifying the Internal Components CPUJ11 Force Zmodem Software Load Sanity TimerTo Clear a Lost Password Connecting to the Console Connector Figure C-3 Rear View of the Console and LAN ConnectorsWAN Interface Connection Pinout InformationModule CSU/DSU ModuleT1/E1 Module T1/E1Universal WAN Module Connecting cable must be a shielded cable Link PinoutsServicing Information RS232C / V.24 Link Pinouts DCERS530 / RS422 Link Pinouts Figure C-8 RS530 / RS422 Link Pinouts11 / X.21 Link Pinouts Figure C-9 V.11 / X.21 Link Pinouts11 / X.21 DB25 to DB15 Connector Cable Figure C-10 V.11 / X.21 DB25 to DB15 Connector CableNull-Modem Cable Configuration Figure C 11 V.35 Null-Modem CableRS232 / V.24 Null-Modem Cable Figure C-12 RS232 / V.24 Null-Modem CableSignal Ground DTE Ready a RS530 / RS422 Null-Modem CableServicing Information Appendix D Software Upgrades Considerations Servicing Information Page PC used for Tftp transfers Link