Black Box HDMCII VDSL2 LAN Extender Module (Extended Temp) manual Host CO Module Configuration

Page 9

Chapter 3: Configuration

Switch #

 

 

Feature

 

Function

 

Default

1

 

 

HOST

HOST=OFF / Remote=ON

 

OFF

2

 

 

LFPT

 

On= Link Fault Pass-Through Enabled

 

OFF

3

 

 

FL

 

ON= Fault Loopback Enabled

 

OFF

4

 

 

Band Plan

 

On= Asymmetric 998 with ISDN

 

OFF

 

 

 

Off= Symmetric 997 with ISDN

 

 

 

 

 

 

 

 

5

 

 

AN

 

On= Auto Negotiation ON

 

ON

6

 

 

Flow Control

 

On= Flow Control ON

 

ON

7

 

 

Selective AN

 

On= Selectively advertises Speed

 

OFF

 

 

 

Duplex if AN is enabled

 

 

 

 

 

 

 

 

8

 

 

Duplex

OFF= Full Duplex / ON= Half Duplex

 

OFF

9

 

 

Speed

 

On= 100Mbps / Off= 10Mbps

 

OFF

10

 

 

Factory Default

 

Factory Default: Do not Use

 

OFF

These features are described in more detail in the following sections.

3.2 Host CO Module Configuration

To allow the HOST (CO) HDMCII VDSL2 LAN Extender Module (Extended Temp) to manage the remotely connected (CPE) HDMCII VDSL2 LAN Extender Module (Extended Temp) unit, set DIP Switch #1 to the OFF position (default setting). This selection can only be performed manually and cannot be overridden by software settings.

A Host configured CO HDMCII VDSL2 LAN Extender Module (Extended Temp) must be installed in a managed chassis to allow SNMP management through iView². The High-Density Media Converter System II chassis series, available in 3, 6 and 20 slots with an optional SNMP Management Module, is recommended. Please refer to the section SNMP Management.

3.3 Remote CPE Module Configuration

To configure a CPE HDMCII VDSL2 LAN Extender Module (Extended Temp) as a Remote CPE, set DIP Switch #1 to the ON position (OFF is the default setting).

A Remote CPE configured HDMCII VDSL2 LAN Extender Module (Extended Temp) can be installed in an unmanaged chassis. These chassis can include Density Media Converter System II chassis with the optional SNMP agent management module removed.

3.4 DATA Port Features

The 10/100BaseT DATA port on the HDMCII VDSL2 LAN Extender Module (Extended Temp) Auto Negotiates for speed and duplex mode. These modules also provide the option of manually setting the speed and duplex mode if the connected devices do not have the ability to Auto Negotiate, or

LMC5601C-VDSL2 724-746-5500 blackbox.com

Page 9

Image 9
Contents Hdmcii VDSL2 LAN Extender Module Extended Temp FCC and IC RFI Statements Blackbox.comFCC and Industry Canada RF Interference Statements Certifications LMC5601C-VDSL2 724-746-5500 blackbox.comCertifications Table of Contents Hdmcii VDSL2 LAN Extender Module Extended Temp Part Numbers DescriptionSpecifications SpecificationsOverview Configuration ConfigurationDIP Switch Settings Host CO Module Configuration Remote CPE Module ConfigurationData Port Features Auto Negotiation Selective AdvertisingSnmp Management Link Quality Forcing Duplex ModeFlow Control Forcing the Data Port SpeedInstall the Hdmcii VDSL2 LAN Extender Module Extended Temp Install the Hdmcii VDSL2 LAN Extender Module Extended TempOperation LED Operation OperationFunction 2-1Hdmcii VDSL2 LAN Extender Module Extended Temp Rate/Reach Pin Signal RJ-11 Port PinoutPin Fault Loopback FL Link Fault Pass-ThroughTroubleshooting TroubleshootingContacting Black Box Fiber Optic Cleaning Guidelines Fiber Optic Cleaning GuidelinesElectrostatic Discharge Precautions Electrostatic Discharge PrecautionsPage LMC5601C-VDSL2 724-746-5500 blackbox.com LMC5601C-VDSL2 Rev